manualshive.com logo in svg

JUMO AQUIS 500 CR, Operating Instructions Manual

Share
Download
JUMO AQUIS 500 CR Operating Instructions Manual Download Page 44

6  Operation 

44

6.11 Controller functions

Simple 
switching
functions

In the JUMO AQUIS 500, simple switching functions, such as alarm contacts 
and limit comparators or the signal from the calibration timer, are configured at 
the parameter level, through the parameters for “Switching output 1 or 2”.

The parameters for the controller channel 1 or 2 respectively must then be set 
to “Off”.

Higher-level 
control 
functions

Higher-level control functions are configured at the parameter level, through 
the parameters for “Controller channel 1 or 2”.

The controller channel parameter must then be set to “Controller 1 or 2”.

Operator level 
parameters

Switching output 1 / 2

Explanation

none

no switching function and 
no control function required

Controller 1

the device should have “higher-level” control

Controller 2

the device should have “higher-level” control

Controller alarm 1 / 2
Controller alarm

 main variable

 main variable

 main variable

 main variable

 Temperature

 Temperature

 Temperature

 Temperature

Sensor fault
Calibration timer
Autorange
USP
USP pre-alarm
PH.-EUR
PH.-EUR pre-alarm

“simple” switching functions

Controller channel 1 / 2
Limit value
Pulse width
Pulse frequency
Continuous
Modulating

“higher-level” control functions

Off

must be selected if “simple” switching 
functions are required

Summary of Contents for AQUIS 500 CR





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands