manualshive.com logo in svg

Julabo CORIO CP-1000F, Original Operating Manual

Share
Download
Julabo CORIO CP-1000F Original Operating Manual Download Page 59

Maintenance 

59

 

9.6  Clean device 

 

The circulator and bath tank, and also a cooling machine if connected, should 
be cleaned from time to time. 
In addition to this, the device must be appropriately decontaminated if 
hazardous substances have been spilled on or into the device. 
 

 

  Lint-free cloth 

 

  Mild cleaning agent 

 

 

 

 

NOTE 

Damage to the electronics due to water penetration! 

Ingress of water can damage electronic components of the device and thus 

lead to failure of the device.

 

•  Clean the outside of the device with a damp cloth only 
•  Prevent water from entering the device 

 

 

  The device is switched off and disconnected from the mains voltage. 

1.  Allow the device to cool down to room temperature. 
2.  Completely drain the bath fluid. 
3.  Clean the surface of the circulator and the bath tank with a damp cloth. 

  Some dish detergent may also be used for cleaning. If in doubt, ask 

technical service for alternative cleaning mediums. 

  The device has now been cleaned. 

 

 

9.7  Device storage 

 

This section describes how to store the device. 
 

 

  The device is switched off and disconnected from the mains voltage. 

1.  Empty all system components completely. 
2.  Clean the device. 
3.  Carefully dry the device and all its system components, e.g. with 

compressed air. 

4.  Close all connections. 
5.  Store the device in a dust-free, dry and frost-free location. 

  The device is protected and can be safely stored there. It can be put into 

operation again as needed. 

 

 

Summary of Contents for CORIO CP-1000F









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands