JTS UF-20R/5 Instruction Manual Download Page 17

17

English

3)  For power supply:

UF-20R / 5:

 Connect the mains jack (11) to 

a mains socket (230 V/ 50 Hz) via the mains 
cable provided 

UF-20S / 5:

 Connect the power supply unit 

provided to the power supply jack (11) and 
to a mains socket (230 V/ 50 Hz)  The receiver 
is provided with a hook for strain relief (12): 
Lead the cable around the hook to prevent 
accidental disconnection of the power supply 
unit from the receiver 

 

 Note:

 The receiver or the power supply unit will 

still consume power when the receiver has been 
switched off  Therefore, always disconnect the mains 
plug or the power supply unit if the transmission 
system is not operated for a longer period of time 

3.1.1  Connecting  multiple  UF-20R / 5

Figure 4 shows interconnection of multiple re-
ceivers UF-20R / 5  For interconnection, only two 
antennas and a mains cable are required  The 
other short connection cables are also supplied 
with the receivers  This is a convenient way of 
interconnecting up to ten UF-20R / 5 

3.2  Switching on/off

1)  Press the button   (10) to switch on the re-

ceiver  In normal mode, the display (6) lights 
up in orange  If it lights up in red and an 
error message appears periodically, the reason 
may be:

  No Signal

 = The wireless microphone /

transmitter has been switched off or uses a 
different transmission frequency than the re-
ceiver (

 chapter 3 5) 

  Mic. Mute

 = The wireless microphone /

transmitter is muted (refer to the correspond-
ing manual) 

 = The batteries of the wireless micro-

phone / transmitter are almost discharged 

AF OUTPUT

BALANCED

AF OUTPUT

BALANCED

AF OUTPUT

BALANCED

AF OUTPUT

BALANCED

RF B Out

Antenna B In

12V   out

RF A Out

Antenna A          

In

12V   out

530-605MHz

Freq. Range:

Serial No.:

AF OUTPUT

BALANCED

AF OUTPUT

BALANCED

AF OUTPUT

BALANCED

AF OUTPUT

BALANCED

RF B Out

Antenna B In

12V   out

RF A Out

Antenna A          

In

12V   out

530-605MHz

Freq. Range:

Serial No.:

AF OUTPUT

BALANCED

AF OUTPUT

BALANCED

AF OUTPUT

BALANCED

AF OUTPUT

BALANCED

RF B Out

Antenna B In

12V   out

RF A Out

Antenna A          

In

12V   out

530-605MHz

Freq. Range:

Serial No.:

Audio channel 1

~ 230 V

Audio channel 2

Audio channel 3

Audio channel 4

10. UF-20R/5

3.
...

1. UF-20R/5

2. UF-20R/5

Audio channel 19

Audio channel 20

Fig. 4  Connecting up to ten UF-20R / 5

Summary of Contents for UF-20R/5

















































Reviews: