background image

Specifications 

9-2 

 

Transmitter 

Antenna output power 

8W - 25W    (Reduced output: 0.5W - 1W)    +20%, -50% 

Oscillation method 

Frequency synthesizer 

Modulation method 

Frequency modulation 

Carrier frequency error 

±1.5kHz or less 

Maximum frequency deviation 

±5kHz or less 

Occupied bandwidth 

16kHz or less 

Pre-emphasis characteristics 

6dB/oct 1dB, -3dB 

Overall distortion 

10% or less 

Adjacent channel power 

-70 dB or 0.2 

μ

W or less 

Unwanted emissions in the 
out-of-band domain 

3.125µW or less 

Unwanted emissions in the spurious 
domain 

3.125µW or less 

Spurious emissions 
(EN300 338, EN301 925) 

9kHz-2GHz: 

0.25µW or less 

2GHz-4GHz: 

1µW or less 

Residual modulation 

-40dB or less 

 

 

Receiver 

Receiving system 

Double superheterodyne 

1st IF 

21.4MHz 

2nd IF 

455kHz 

Local oscillation frequency 

Reception frequency - 21.4 MHz 

Local oscillation method 

Frequency synthesizer 

Frequency accuracy 

±10 x 10

-6

 or less 

Sensitivity (phone) 

6dB 

μ

V or less    (SINAD=20dB) 

Sensitivity (DSC) 

1% or lower symbol error rate at 0dB 

μ

Selectivity 

6dB bandwidth: 12kHz or more, 70dB selectivity: 25kHz or less 

Signal-to-Noise ratio 

40dB or more 

Audio output variance 

3dB or less 

De-emphasis characteristics 

6dB/oct, 1dB, -3dB 

Co-channel selectivity 

-10 - 0dB 

Adjacent channel selectivity 

Sensitivity ratio 80dB or more 

Desensitization effect (phone) 

80dBµV or more 

Desensitization effect (DSC) 

Symbol error rate of 1% or better at a wanted signal level of 3dB 

μ

and an unwanted signal level of 73dB 

μ

Spurious response (phone) 

Sensitivity ratio 70dB or more 

Spurious response (DSC) 

Symbol error rate of 1% or better at a wanted signal level of 3dB 

μ

and an unwanted signal level of 73dB 

μ

Intermodulation characteristics 
(phone) 

65dBµV or more 

Intermodulation characteristics 
(DSC) 

Symbol error rate of 1% or better at a wanted signal level of 3dB 

μ

and an unwanted signal level of 73dB 

μ

Blocking characteristics 

90dBµV or more 

Radiation 

9kHz - 2GHz: 

2nW or less 

2GHz - 4GHz: 

20nW or less 

Squelch mute 

-40dB or less 

Squelch open level 

+6dBµV or less 

Overall distortion 

10% or less 

 

Summary of Contents for JHS-770S -



































































































































































Reviews: