Important Testing Guidelines
8
10
9
1.
Sit in a calm environment for at least 5 minutes prior to testing.
3
. Wait 3 minutes or longer before re-testing.
7
. Test comparisons should only be made when monitor is used on the same arm, in the
same position, and at the same time of day.
9. This blood pressure monitor is not recommended for people with severe arrhythmia.
Avoid eating, exercising, and bathing for 30 minutes prior to testing.
2.
. Do not stand while testing. Sit in a relaxed position while keeping your arm level with
your heart.
4. Avoid speaking or moving body parts while testing.
5. While testing, avoid strong electromagnetic interference such as microwave ovens and
cell phones.
6
. Try to measure your blood pressure at the same time each day for consistency.
8
Any blood pressure recording can be affected by the following factors
:
1. The position of the subject, his or her physiologic condition;
2. The performance and accuracy of the device;
3. Cuff size: too small cuff (bladder) will produce a higher blood pressure value than usual,
too big cuff (bladder) will produce a lower blood pressure value;
4. Measuring position does not keep level with your heart;
5. Speaking or moving body parts while testing;
6. Not relaxing for about 5 minutes before taking the measurement.
10. Do not use this blood pressure monitor if the device is damaged.
Quick Start
1. Install batteries
2. Insert cuff air plug into the behind side of monitor unit. (See Figure B)
. (See Figure A )
3. Remove thick clothing from the arm area.
4. Rest for several minutes prior to testing. Sit down in a quietplace comfortably ,
back and arm support on a desk or table ,withyour legs uncrossed ,your arm
resting on a firm and your feet flat on the floor. (See Figure C )
5. Apply cuff to your left arm and middle of the cuff at the level of your heart. Bottom
of cuff should be placed approximately 1-2cm (1/2'') above elbow joint. (See Figures D&E)
1-
2c
m
''
(0
.4
-0
.8
)
Unit Operation
Battery Installation
Slide battery cover off as indicated by arrow.
Install 4 new AA alkaline batteries according to polarity.
Close battery cover.
Figure C
Figure D
Figure E
6. Press " START/STOP " Button to start testing.
AC Adapter jack is on the back side of the monitor. Medical AC adapter(DC 5.0 V,1000mA)
can be used with the device (recommended, not provided). The adapter connect pin should
be positive inside and negtive outside with a 2.1mm coaxial joint.
Do not use any other type of AC adaptor as it may harm the unit.
Unit Illustration
7
Note:Power supply is specified as part of ME EQUIPMENT.
Display
Contents
3.Arm Cuff
2.Owner's Manual
1.Monitor Unit
Owner's Manual
Arm-type Fully Automatic
Digital Blood Pressure Monitor
Model
DBP-6277B
Arm Type
5.2MOPPMedical AC Adapter(DC5.0 V,1000mA)
(recommended, not provided)
4.Storage Bag
1~
2c
m
(0
.4
~0
.8
in
ch
)
22
~3
6c
m
（
8.
6~
14
.2 i
nc
h
)
M
ai
n
Ar
te
ry
LE
FT
AR
M
IN
D
E
X
Group1
Systolic
Blood
Pressure
Diastolic
Blood
Pressure
Pulse Rate
Irregular Heartbeat
Indicator
Bluetooth
Indicator
Time/Date
Blood Pressure
Indicator
Heart Rate Indicator
WHO Blood Pressure
Classification Indicator
Last 3 Tests Average
Low Battery Indicator
Arm Shake Indicator
Cuff Loose Indicator
Group2
PUL
/
min
OK
Bluetooth
SMART
AM
PM
BP
mmHg
Figure A
Figure B
USB Adapter Jack