Jøtul GF 160 DV IPI Installation And Operation Instructions Manual Download Page 42

42

139894 GF 160 DV IPI   12/17

This warranty policy applies to gas products identified by the 

Jøtul trade name as set forth below.

A. LIMITED FIVE YEAR WARRANTY - Cast Iron, Steel Doors, 

Surround Components, Firebox:

Jøtul North America Inc. (JØTUL) warrants, to the original retail 

purchaser, that those components of the Jøtul Gas Stove or 

Fireplace specified above will be free of defects in material and 

workmanship for a period of five (5) years from the date of 

purchase.  This warranty is subject to the terms, exclusions and 

limitations set forth in the following text.

B.  LIMITED TWO YEAR WARRANTY - Burner, Ceramic Burner, 

BurnerTreatments, Firebox Panels:

 

JØTUL warrants, to the original retail purchaser, that those 

components of the Jøtul Gas Stove or Fireplace specified above 

will be free of defects in material and workmanship for a period 

of two (2) years from the date of purchase. 

Ceramic burners

 are 

warranted against functional defects for a period of two (2) 

years from the date of purchase.This warranty is subject to the 

terms, exclusions, and limitations set forth in the following text.

C. LIMITED TWO YEAR WARRANTY - Enamel Finish: 

JØTUL warrants, to the original retail purchaser, the enamel 

finish on cast iron components of the Jøtul Stove or Fireplace 

Insert specified above against peeling or fading for a period of 

two (2) years from the date of purchase. This warranty is subject 

to the terms, exclusions and limitations set forth below.

D. LIMITED ONE YEAR WARRANTY - Gas & Electrical Components 

(controls, plumbing, valve, blower)

JØTUL warrants, to the original retail purchaser, that those 

components of the Jøtul Gas Stove or Fireplace specified above 

will be free of defects in material and workmanship for a period 

of one (1) year from the date of purchase. This warranty is 

subject to the terms, exclusions, and limitations set forth in the 

following text.

JØTUL will repair or replace (including parts & labor), at its option, any 

of the above components determined by JØTUL to be covered by this 

warranty. You must, at your own expense, arrange to deliver or ship 

the component to an authorized Jøtul dealer and arrange for pickup 

or delivery of the component after repairs have been made.  If, upon 

inspection, JØTUL determines that the component is covered by this 

warranty, the repair or replacement will be made as set forth above. 

This warranty is not transferable and is extended only to, and is solely 

for the benefit of, the original retail purchaser of the Jøtul Gas Stove or 

Fireplace. This paragraph sets forth the sole remedy available under this 

warranty in the event of any defect in the Jøtul Gas Stove or Fireplace.

The warranty period for any replaced component will be the remaining 

unexpired portion of the warranty period for the original component.

Please retain your dated sales receipt in your records as proof of purchase.

 

EXCLUSIONS AND LIMITATIONS

NOTICE: This warranty is void if installation or service is performed 

by someone other than an authorized installer, service agency or gas 

supplier, or if installation is not in conformance with the installation and 

operating instructions contained in this owner’s manual or local and/

or national fire and building regulations.  A listing of local authorized 

installers, service agencies and gas suppliers can be obtained from the 

National Fireplace Institute at http://www.nficertified.org/.  

This warranty does not cover the following:

1)   Repair or replacement of parts that are subject to normal wear and 

tear during the warranty period or to parts that may require replacement 

in connection with normal maintenance. These parts include gaskets and 

glass (except to the extent such parts suffer damage from thermal stress).

2)  Damage due to incorrect installations not in conformance with the 

installation instructions contained in this owner’s manual or local and/or 

national fire and building regulations.

3)  Damage due to service performed by an installer, service agency or gas 

supplier, unless otherwise agreed to in writing by JØTUL. 

4)  Labor or other costs associated with the repair of gas controls, 

plumbing, burners, log set, or sheet metal firebox beyond the warranty 

period.

5)  Damage caused by unauthorized modification, use or repair.

6)  Damage to enameled surfaces caused by improper operation or 

misuse, including use that is not in conformance with the operating 

instructions contained in this owner’s manual. Such damage can typically 

be identified by bubbling, cracking, or discoloration of the enamel finish.

7)  Costs incurred by travel time and/or loss of service.

8)  Damage incurred while the Jøtul Gas Stove or Fireplace is in transit.

IN NO EVENT SHALL JØTUL, ITS PARENT COMPANY, SHAREHOLDERS, 

AFFILIATES, OFFICERS, EMPLOYEES, AGENTS OR REPRESENTATIVES BE 

LIABLE OR RESPONSIBLE TO YOU FOR ANY SPECIAL, INDIRECT, INCIDENTAL, 

CONSEQUENTIAL, PUNITIVE OR OTHER SIMILAR DAMAGES, INCLUDING, 

BUT NOT LIMITED TO, LOST PROFITS, LOST SALES, INJURY TO PERSON OR 

PROPERTY, OR DAMAGES TO A STRUCTURE OR ITS CONTENTS, ARISING 

UNDER ANY THEORY OF LAW WHATSOEVER.  ALL IMPLIED WARRANTIES, 

INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND 

FITNESS FOR A PARTICULAR PURPOSE, OR OTHERWISE, ARE LIMITED IN 

DURATION TO THE LENGTH OF THIS WRITTEN WARRANTY.  EXCEPT AS 

EXPRESSLY SET FORTH HEREIN, JØTUL MAKES NO ORAL, WRITTEN OR 

OTHER WARRANTY WITH RESPECT TO JØTUL GAS STOVES OR FIREPLACES.

Some states do not allow the exclusion or limitation of incidental 

or consequential damages, or limitations on the length of implied 

warranties.  Therefore, the above exclusions or limitations may not apply 

to you.  This warranty gives you specific legal rights, and you may have 

other rights, which vary from state to state. 

JØTUL reserves the right to discontinue, modify or change the materials used 

to produce the Jøtul Gas Stove or Fireplace.  JØTUL shall have the right to 

replace any defective component with substitute components determined by 

JØTUL to be of substantially equal quality and price. 

The dollar value of JØTUL’s liability for breach of this warranty shall be 

limited exclusively to the cost of furnishing a replacement component.  

JØTUL shall not in any event be liable for the cost of labor expended 

by others in connection with any defective component.  Any costs or 

expenses beyond those expressly assumed by JØTUL under the terms of 

this warranty shall be the sole responsibility of the owner(s) of the Jøtul 

Gas Stove or Fireplace.

No dealer, distributor, or other person is authorized to modify, augment, 

or extend this limited warranty on behalf of JØTUL.  NO MODIFICATION 

OR CHANGE TO THIS WARRANTY WILL BE EFFECTIVE UNLESS IT IS MADE IN 

A WRITTEN DOCUMENT MANUALLY SIGNED BY AN AUTHORIZED OFFICER 

OF JØTUL.

An authorized installer may have been provided with certain information 

related particularly to the Jøtul Gas Stove or Fireplace; however, no 

authorized installer or other person who may service the appliance is 

an agent of JØTUL.  No inference should be made that JØTUL has tested, 

certified, or otherwise pronounced any person as qualified to install or 

service the appliance.  JØTUL shall not be liable or otherwise responsible 

for any error or omission by a person installing or servicing a Jøtul Gas 

Stove or Fireplace.

If you believe your Jøtul Gas Stove or Fireplace is defective, you should 

contact your nearest authorized Jøtul dealer, who will process a warranty 

claim.  IN ORDER TO QUALIFY FOR WARRANTY COVERAGE, JØTUL MUST 

RECEIVE NOTICE OF A POSSIBLE DEFECT WITHIN SIXTY (60) DAYS OF THE 

DATE THE DEFECT IS FIRST DISCOVERED, OR REASONABLY COULD HAVE 

BEEN DISCOVERED.

This warranty is given by Jøtul North America, Inc.,  

55 Hutcherson Drive, Gorham, Maine 04038 USA 

18.  Jøtul Gas Product  

Warranty

Summary of Contents for GF 160 DV IPI













































Reviews: