22
is best indicated by yellow, flickering flames under the baffle.
• Then regulate the rate of combustion to the desired level of
heating by adjusting the air vent
(fig. 12 A)
.
See the general manual for information regarding use of the
stove.
4.0 Service
Warning!
Any unauthorised change to the product is illegal.
Only use original spare parts.
4.1 Replacing the baffle/exhaust
deflector (fig. 9 and 12)
(
N.B.
If you use tools, be aware that the vermiculite plates may
be damaged by rough treatment).
1. Lift up the front edge of the baffle plate and tilt it out
(fig. 12G)
.
Remove the side burn plates
(fig. 12 F)
and the rear burn plate
(fig. 12 E)
.
2. The exhaust deflector, in cast-iron - that is located above the
baffle plate, rests with the bar on the ribs at the rear flue
outlet
(fig. 9 A)
. Lift the exhaust deflector slightly up, pull it
forward and tilt it out.
3. For reassembly follow the same procedure for installation,
but in reverse.
4.2 Replacement of burn plates/base
plate (fig. 10 and 12)
(
N.B.
If you use tools, be aware that the vermiculite plates may
be damaged by rough treatment).
1. Lift up the front edge of the baffle plate and tilt it out. Remove
the side burn plates
(fig. 12 F)
and the rear burn plate
(fig. 10 E)
.
2. Then lift up the grate and the base plate and take it out
(fig.
12 D)
.
3. Follow the same procedure for installation, but in the opposite
sequence.
4. When reassembling the grate and the base plate, make sure
that the riddling bar
(fig. 10A)
that moves the riddling grate
is threaded into the slot on the right edge of the grate.
4.3 Replacing the inner/outer side
glass (fig. 23, 26, 27 and 27)
1. Lift up the front edge of the baffle plate and tilt it out Remove
the side burn plates
(fig. 26F)
and the rear burn plate
(fig. 26E)
.
2. The exhaust deflector, in cast-iron - that is located above the
baffle plate, rests with the bar on the ribs at the rear flue
outlet
(fig. 23 A)
. Lift the exhaust deflector slightly up, pull it
forward and tilt it out.
3. Remove riddling grate, base plate and ash pan
(fig. 26 D).
4. Unscrew the upper and lower screws
(fig. 27 A and 28 A)
, and
tilt the glass holder with the glass carefully out through
the door.
N.B.
The glass holder also keeps the outer glass
in place
5. Remove the glass and possibly replace gaskets. If needed
replace the external glass.
6. For reassembly follow the same procedure for installation,
but in reverse
.
5.0 Optional equipment
5.1 Decoration plates
Decoration plates, reed (2 units), black paint
- cat. no. 350988
Decoration plates, cover for side windows (2 units), black paint
- cat. no. 350990.
Soapstone, top 25 mm one-piece -
cat. no. 350992.
Soapstone, top 25 mm three-piece -
cat. no. 361011 (substitute for
350992 installed with steel chimney).
5.2 Rotating set
(See separate installation manual)
Rotating set for Jøtul F 373,
- cat. no. 350997
ENGLISH
Summary of Contents for F 373 ADVANCE
