21
ENGLISH
calculating the correct chimney cross-section.
• Several solid fuel fired appliances can be connected to the
same chimney if the chimney’s cross-section is sufficient.
• Connection to the chimney must be carried
o u t i n a c c o r d a n c e w i t h t h e i n s t a l l a t i o n
instructions from the supplier of the chimney.
• Before making a hole in the chimney the fireplace should be
test-mounted in order to correctly mark the position of the
fireplace and the hole in the chimney. See
fig. 1
for minimum
dimensions.
• Ensure that the flue pipe is inclined all the way up to the chimney.
• Use a flue pipe bend with a sweeping hatch that allows it to
be swept.
Be aware of the fact that it is particularly important that
connections have a certain flexibility in order to prevent
movement in the installation leading to cracks.
Chimney draught; See «2.0 Technical data». If the draught is
too strong you can install and operate a flue damper to control
the draught.
Assembly of flue pipe with top outlet (fig. 7)
The product is supplied from the factory with the smoke outlet
mounted for top outlet.
1. Put the top plate
(fig. 7 C)
on the product.
2. Obtain assistance in lifting the top grate
(fig. 7 A)
and holding
it up while the flue is fastened.
3. Thread the flue pipe through the grate of the top plate and
place it on the smoke outlet of the top outlet.
4. Tighten well with gasket.
Assembly of flue pipe with rear outlet
(fig. 1, 3, 7 and 8)
The product is supplied from the factory with the smoke outlet
mounted for top outlet. If you want a rear outlet, do the following:
1. Place the product in correct position
(fig. 1)
.
2. When changing to rear outlet, the smoke outlet
(fig. 3B)
is
unscrewed from the top outlet.
3. Unscrew the cover for the rear outlet from the inside of the
burn chamber
(fig. 3A)
.
4. Place the gasket on the end of the flue pipe
(fig. 8 A)
.
5. Mount the smoke outlet
(fig. 8 B)
on the end of the flue pipe
that is fitted with the gasket.
6. Mount the flue pipe and smoke outlet from the inside of the burn
chamber and attach the smoke outlet using M8x30 mm screws.
N.B. If the flue pipe is longer than 350 mm it has to be assembled
into the smoke outlet from the outside of the product.
7. Fasten the cover to the top outlet
(fig. 7)
with the screws that
fastened the smoke outlet.
N.B.
It is important that the joints/flue pipes are completely
sealed. Air leaks can prevent the flue pipe from functioning
properly.
3.4 Mounting of the product -
(fig. 9, 10 and 11)
1. Place the baffle plate with the bar in the groove on the ribs
(fig. 9 A)
.
2. Move the base plate through the opening and place it on
the bottom.
3. Place the riddling grate in position on the base plate. Check
that the riddling grate’s slot on the right side is entered into
the riddling bar
(fig. 10 A)
.
4. Place the ash pan at the bottom of the product.
5. Place the rear burn plate in the base plate’s rear groove.
6. Place the side burn plates on each side in the base plate’s side
grooves. Move the baffle plate in and place it so that it rests
on the side and rear burn plates.
7. Hold the baffle plate while the other side burn plate is
mounted.
8. Let the baffle plate rest on the burn plates.
9. Place the small side burn plates
(fig. 11 A)
in the base plate’s
groove under the side glasses.
10. Replace the top plate with the top grid and bowl.
11. Place the product data plate which is in the ash pan,
underneath the burn chamber.
3.5 Control of functions (fig. 12)
When the product is set up, always check the control functions.
These shall move easily and function satisfactorily.
Jøtul F
373
is equipped with the following controls:
Air vent fig. 12 A
Pushed in:
Closed
Pulled out:
Open
Ignition vent, fig. 12 B
Pushed in:
Closed
Pulled out:
Open
Riddling grate (same handle as for the ignition vent) (Fig. 12B)
Right handle is pushed in and out.
Handle for door fig. 12 C:
Is opened by pulling handle out.
3.6 Ash removal
Jøtul F
373
has an ash pan which makes it easy to remove the ashes.
1. Only remove ashes when the fireplace is cold.
2. Push/pull the handle for the ash grate/ignition vent out and in
several times so that the ashes fall down into the ash pan. Use
something like a glove to grab the handle on the ash pan.
3. Make sure that the ash pan doesn’t fill up so high that it keeps
ash from coming through the grate into the pan.
4. Make sure the door to the ash pan is securely shut when the
stove is in use.
For the rest, see description of how to handle ash in the Manual
on general use and maintenance in Point
«6.1 Fire preventive
measures».
3.7 Use (fig. 12)
• Open the air vent and the ignition vent by pulling it out all
the way
(fig. 12)
. If necessary, keep the door slightly open.
(Use a glove, for example, as the handle can become hot.)
• Place two medium sized logs in/out on each side of the base.
N.B
. In order to avoid sooting on the glass, it is important that
the log is not placed adjacent to the glass on the product.
• Crumple some newspaper (or birch bark) between these and
add some kindling wood in a criss-cross pattern on top and
light the newspaper.
• Gradually increase the size of the fire, but the wood should
not be stacked higher than the horizontal holes on the back
burn plate. See
fig. 12 H
.
• Close the ignition vent
(fig. 12 B)
when the firewood has
ignited and the fire is burning well.
• Check that the afterburning (secondary combustion) starts. This
Summary of Contents for F 373 ADVANCE
