background image

Published in U.S.A.

www.johnsoncontrols.com

TEC22x6(H)-4 and TEC22x6H-4+PIR Series L

ON

W

ORKS

® Network Thermostat Controllers with 

Dehumidification Capability, Fan Control, and Occupancy Sensing Capability Installation Instructions

24

Metasys® and Johnson Controls® are registered trademarks of Johnson Controls, Inc.

All other marks herein are the marks of their respective owners. © 2010 Johnson Controls, Inc.

Building Efficiency

507 E. Michigan Street, Milwaukee, WI  53202

Technical Specifications     

TEC22x6(H)-4 and TEC22x6H-4+PIR Series L

ON

W

ORKS

 Network Thermostat Controllers with 

Dehumidification Capability, Fan Control, and Occupancy Sensing Capability

Power Requirements

19 to 30 VAC, 50/60 Hz, 2 VA (Terminals 4 and 5) at 24 VAC Nominal, Class 2 or 
Safety Extra-Low Voltage (SELV)

Triac Output 
Rating (BO1, 
BO2, BO3, 
BO4)

On/Off and 
Floating 
Control

19 to 30 VAC, 1.0 A Maximum, 15 mA Minimum, 3.0 A In-Rush

Analog Output 
Rating

Proportional 
Control

0 to 10 VDC into 2k ohm Resistance (Minimum)

Fan Relay Output Rating

19 to 30 VAC, 1.0 A Maximum, 15 mA Minimum, 3.0 A In-Rush

Auxiliary 
Output Rating

Triac Output

19 to 30 VAC, 1.0 A Maximum, 15 mA Minimum, 3.0 A In-Rush

Analog Inputs

Resistive Inputs (RS and UI3) for 10k ohm Johnson Controls Type II Negative 
Temperature Coefficient (NTC) Thermistor Sensors

Binary Inputs

Voltage-Free Contacts across Terminal Scom to Terminals BI1, BI2, or UI3

Temperature Sensor Type

Local 10k ohm NTC Thermistor

Wire Size

Unshielded Twisted Pair - 22 AWG (0.6 mm Diameter) Minimum, 18 AWG (1.0 mm 
Diameter) Recommended

L

ON

W

ORKS

 Network Standard

64 Devices Maximum without a Repeater, 127 Devices Maximum with a Repeater; 
6,250 ft (1,905 m) Maximum (Bus Topology)

Temperature 
Range

Backlit Display

-40.0°F/-40.0°C to 122.0°F/50.0°C in 0.5° Increments

Heating 
Control

40.0°F/4.5°C to 90.0°F/32.0°C

Cooling 
Control

54.0°F/12.0°C to 100.0°F/38.0°C

Accuracy

Temperature

±0.9F°/±0.5C° at 70.0°F/21.0°C Typical Calibrated

Humidity

±5% RH from 20 to 80% RH at 50 to 90°F (10 to 32°C)

Minimum Deadband

2F°/1C° between Heating and Cooling

Ambient 
Conditions

Operating

32 to 122°F (0 to 50°C); 95% RH Maximum, Noncondensing

Storage

-22 to 122°F (-30 to 50°C); 95% RH Maximum, Noncondensing

Compliance

United States

UL Listed, File E27734, CCN XAPX, 
Under UL 873, Temperature Indicating and Regulating Equipment
FCC Compliant to CFR 47, Part 15, Subpart B, Class A 
L

ON

M

ARK

® Certification 3.4

Canada

UL Listed, File E27734, CCN XAPX7, Under
CAN/CSA C22.2 No. 24, Temperature Indicating and Regulating Equipment
Industry Canada, ICES-003

Europe

CE Mark, EMC Directive 2004/108/EC, standards EN 61000-6-3 and EN 61000-6-1

Australia and 
New Zealand

C-Tick Mark, Australia/NZ Emissions Compliant

Shipping Weight

TEC22x6(H)-4 Models:

 0.75 lb (0.34 kg)

TEC22x6H-4+PIR Models:

 0.77 lb (0.35 kg)

The performance specifications are nominal and conform to acceptable industry standards. For application at conditions beyond these 
specifications, consult the local Johnson Controls office. Johnson Controls, Inc. shall not be liable for damages resulting from misapplication or 
misuse of its products.

Summary of Contents for TEC2216-4

























Reviews: