Johnson Controls TEC22 4-3 Series Installation Instructions Manual Download Page 17

Published in U.S.A.

www.johnsoncontrols.com

TEC22x4-3 L

ON

W

ORKS

® Networked Multi-Stage Economizer Thermostats Installation Instructions

 17

Controls Group

507 E. Michigan Street
Milwaukee, WI  53202

© 2006 Johnson Controls, Inc.

Accuracy

Temperature

±0.9F°/±0.5C° at 70.0°F/21.0°C Typical Calibrated

Minimum Deadband

2F°/1C° between Heating and Cooling

Ambient 
Conditions

Operating

32 to 122°F (0 to 50°C); 95% RH Maximum, Noncondensing

Storage

-22 to 122°F (-30 to 50°C); 95% RH Maximum, Noncondensing

Compliance

United States

UL Listed, File E27734, CCN XAPX, 
Under UL 873, Temperature Indicating and Regulating Equipment

FCC Compliant to CFR 47, Part 15, Subpart B, Class A
L

ON

M

ARK

® Certification 3.4 (pending)

Canada

UL Listed, File E27734, CCN XAPX7, 
Under CAN/CSA C22.2 No. 24, Temperature Indicating and Regulating Equipment

Industry Canada, ICES-003

Europe

CE Mark, EMC Directive 89/336/EEC

Australia and 
New Zealand

C-Tick Mark, Australia/NZ Emissions Compliant

Shipping Weight

0.75 lb (0.34 kg)

The performance specifications are nominal and conform to acceptable industry standards. For application at conditions beyond these 
specifications, consult the local Johnson Controls office. Johnson Controls, Inc. shall not be liable for damages resulting from misapplication or 
misuse of its products.

TEC22x4-3 L

ON

W

ORKS

 Networked Multi-Stage Economizer Thermostat (Part 2 of 2)

Summary of Contents for TEC22 4-3 Series


















Reviews: