background image

TEC22x4-3 L

ON

W

ORKS

® Networked Multi-Stage Economizer Thermostats Installation Instructions

8

TOccTime

Sets the duration of the Tempo-
rary Occupancy Time (when the 
thermostat is in the Unoccupied 
mode) when a Schedule Over-
ride Function is enabled using ei-
ther the Main User Menu or DI1 
or DI2 configured as a temporary 
override remote contact 
(RemOVR).
Sets the effective duration of the 
Temporary heating or cooling 
setpoints set using the up/down 
arrow keys.

default: 

3.0 hrs

Range: 

0.0

 to 

12.0 hrs

 adjustable in 1-hour increments

Cal RS

Sets the desired room air 
temperature sensor calibration 
(offset). The offset can be added to 
or subtracted from the actual 
displayed room temperature.
Default: 

0.0F°/0.0C°C

Range: 

-5.0F°/-2.5C°

 to 

5.0F°/2.5C°

 adjustable in 1.0F°/0.5C° 

increments

Cal OS

Sets the desired outdoor air 
temperature sensor calibration 
(offset). The offset can be added to 
or subtracted from the actual 
displayed room temperature.
Default: 

0.0F°/0.0C°

Range: 

-5.0F°/-2.5C°

 to 

5.0F°2.5C°

 adjustable in 1.0F°/0.5C° 

increments

H stage

Reverts the operation of a two-stage 
thermostat to a single-stage 
thermostat when the second heating 
stage is not needed.
Default: 

2.0

(1.0):

 One Stage

(2.0):

 Two Stages

C stage

Reverts the operation of a two-stage 
thermostat to a single-stage 
thermostat when the second cooling 
stage is not needed.
Default: 

2.0

(1.0):

 One Stage

(2.0):

 Two Stages

H lock

Discontinues heating operation in 
response to the outdoor air 
temperature. Requires that an 
outdoor air temperature sensor be 
installed and connected.
Default: 

120°F/49°C

Range: 

-15°F/-26°C

 to 

120°F/49°C

 adjustable in 5F°/5C° increments

C lock

Discontinues cooling operation in 
response to the outdoor air 
temperature. Requires that an 
outdoor air temperature sensor be 
installed and connected. C lock 
does not disable economizer free 
cooling operation.
Default: 

-40°F/-40°C

Range: 

-40°F/-40°C

 to 

95°F/35°C

 adjustable in 5F°/5C° increments

2/4event

4

Sets the number of events within a 
24-hour period.
Default: 

2.0

(2.0):

 Two events (one occupied and one unoccupied) within a 

24-hour period

(4.0):

 Four events (two occupied and two unoccupied) within a 

24-hour period

Table 2:  Installer Configuration Menu  (Part 3 of 5)

Parameter 
Appearing 
on Display

Description and Default

Selection Options

Summary of Contents for TEC22 4-3 Series


















Reviews: