Johnson Controls M9200 Series Quick Start Manual Download Page 11

Page: 11 / 12

M9200 Series Electric Spring Return Actuator Product/Technical Bulletin 11

rdering Information

Table 3: Actuators Available

M9200 Series

Electric Motor

Spring Return Actuator

140 lb·in (16 N·m)

M9216-AGA-2

M9216-AGC-2

M9216-AGD-2

M9216-AGE-2

M9216-BGA-2

M9216-BGC-2

M9216-HGA-2

M9216-HGC-2

M9216-JGA-2

M9216-JGC-2

On/Off Control

* * * *

Floating Control

Proportional Control

VDC and mA Input
with Zero and Span

Resistive Input Control

Feedback

135 ohm Potentiometer

1000 ohm Potentiometer

0 to 10 VDC Feedback

2 Auxiliary Switches

* Can be used with 2-wire on/off control.

Note: All models (except the BGA and BGC) have a 25-second
delay upon startup.

Table 4: Accessories Available

Product

Code Number

Description

DMPR-KR003

Sleeve Pin Kit (for Johnson Controls RD-2000 round dampers with a 5/16 in. diameter shaft)*

DMPR-KC003

Blade Pin Extension without Bracket (for Johnson Controls CD-1300 direct-mount applications)

DMPR-KC254

Inside Frame Mounting Kit (for Johnson Controls damper applications requiring the actuator within the
airstream)

M9000-100

Conduit Adaptor Kit

M9000-103

14 VA Transformer, 120/24 VAC, 60 Hz

M9000-104

14 VA Transformer, 230/24 VAC, 60 Hz

M9000-151

Base Mount Linkage Kit (for remote inside duct floor mounting)

M9000-153

Crank Arm Kit (for remote mounting)

M9000-154

1 in. Jackshaft Coupler (for mounting on a 1 in. diameter damper shaft)

M9000-200

Commissioning Tool (provides a control signal to drive proportional [voltage, current, resistive], floating, or
on/off actuators)

M9000-500

Valve Linkage Kit (for field mounting M9216 actuators to Johnson Controls VG7000 1/2 in. through 2 in.
globe-style valve bodies)

M9000-510

Valve Linkage Kit (for field mounting the M9108, M9116, M9124, and M9216 actuators to
VG1000 1/2, 3/4, 1, and 1-1/4 in. ball valves, DN15, DN20, DN25, and DN32)

M9000-511

Valve Linkage Kit (for field mounting the M9124 actuator to the VG1000 1-1/2 in. ball valve, DN40)

* Furnished with the damper and can be ordered separately.

Summary of Contents for M9200 Series













Search results

Summary of Contents for M9200 Series

Reviews:

Related manuals for M9200 Series

Brands by name

Popular brands

Johnson Controls M9200 Series, Quick Start Manual

Search results

Summary of Contents for M9200 Series

Reviews:

Related manuals for M9200 Series

Brands by name

Popular brands