Johnson Controls FAC2611 Installation Manual Download Page 23

Page: 23 / 24

Table 10: FAC2611 Field Application Controller

United States:

UL Listed, File E107041, CCN PAZX, UL 916, Energy Management

Equipment
FCC Compliant to CFR47, Part 15, Subpart B, Class A

Canada:

UL Listed, File E107041, CCN PAZX7 CAN/CSA C22.2 No.205, Signal Equipment

Industry Canada Compliant, ICES-003

Europe:

Johnson Controls declares that this product is in compliance with the essential

requirements and other relevant provisions of the EMC Directive.

Australia and New Zealand:

RCM Mark, Australia/NZ Emissions Compliant

Compliance

BACnet International:

BACnet Testing Laboratories (BTL) Protocol Revision 7 Listed

BACnet Advanced Application Specific Controller (B-ASC)

The performance specifications are nominal and conform to

acceptable industry standard. For application at conditions

beyond these specifications, consult the local Johnson

Controls

office. Johnson Controls shall not be liable for

damages resulting from misapplication or misuse of its

products.

Product warranty

This product is covered by a limited warranty, details

of which can be found at

www.johnsoncontrols.com/

buildingswarranty

Single point of contact

APAC

Europe

NA/SA

JOHNSON CONTROLS
C/O CONTROLS PRODUCT
MANAGEMENT
NO. 32 CHANGJIJANG RD NEW
DISTRICT
WUXI JIANGSU PROVINCE 214028
CHINA

JOHNSON CONTROLS
WESTENDHOF 3
45143 ESSEN
GERMANY

JOHNSON CONTROLS
507 E MICHIGAN ST
MILWAUKEE WI 53202
USA

For more contact information, refer to

www.johnsoncontrols.com/locations

FAC2611 Advanced Application Field Equipment Controller Installation Guide

Summary of Contents for FAC2611

























Search results

Summary of Contents for FAC2611

Reviews:

Related manuals for FAC2611

Brands by name

Popular brands

Johnson Controls FAC2611, Installation Manual

Search results

Summary of Contents for FAC2611

Reviews:

Related manuals for FAC2611

Brands by name

Popular brands