background image

6

 

 

 

 

 

The gas cylinder should only be changed in a ventilated area, away from  sources of 
ignition (candles, cigarettes, and other flame producing appliances) 
Do not obstruct the ventilation holes of the cylinder housing 
Switch off the gas tap after use when using red propane cylinders. 
Switch off the regulator after use when using green propane cylinders. 
In the event of gas leak, the appliance shall not be used or if alight, the gas regulator 
should be turned off immediately and the appliance should be inspected thoroughly 
before it is used again. 
Inspect the gas hose before every use. If it shows signs of cracking, splitting or other 
deterioration it  should be replaced

  with

 

new hose of the same length and of the 

equivalent quality. 
The use of this appliance in enclosed areas can be dangerous and is 

PROHIBITED

For connection of hose and regulator, and connection of regulator and hose, please 
refer to the photos shown below. 

To assist connecting the regulator, carefully place the rubber hose into an insulated cup of 
boiling hot water. This allows the rubber hose to expand and allow the regulator to be 
connected easily. After connecting the regulator, tighten the hose clip with a screwdriver. 

This product contains small batteries. Swallowed small batteries can cause 
CHOCKING HAZARD. Seek immediate medical attention if batteries are swallowed 
or inhaled. Keep children away from the small batteries. 

HEATER STAND AND LOCATION  

The heater is primarily for outdoor use only. Always ensure that adequate fresh air 
ventilation is provided. 
Always maintain proper clearance to non protected combustible materials i.e. top 100 
cm and sides 100 cm minimum. 

 

Heater must be placed on level firm ground. 
Never operate heater in an explosive atmosphere like in areas where gasoline or 
other flammable liquids or vapors are stored. 
To protect heater from strong wind, anchor the base securely to the ground with 
screws. 

Gas Requirements

 

This heater is primarily designed to be used with propane gas. 
Butane gas may also be used with the appropriate regulator however butane freezes 
at zero degrees so will not be ideal to be used during cold temperatures.

 

A dented, rusted or damaged cylinder may be hazardous and should be checked by 
your gas supplier before being used with this heater. 
Never connect an unregulated cylinder to the heater. 

CEILING

100 cm

100 cm

Summary of Contents for JMC-OSPH-SS











Reviews: