background image

10

9

 

 

 

 

  

 

 

 

 

 

CLEANING AND CARE 

• 

Wipe off surfaces with soft, moist cloth.  Do not clean the heater with cleaning 
products that are combustible or corrosive. 

• 

Remove debris and insects from the burner periodically to keep it clean and safe 
for use. 

• 

Cover the burner unit with the optional protective cover when the heater is not in 
use. 

 

PARTS AND SPECIFICATION

 

2270 mm

900 mm

650 mm

730 mm

Reflector

Glass Tube

Top Plate Assy

Protective Guard

Upper Support

Front Panel

Side Panel

Lower Support

Bottom plate

 

 

CONSTRUCTION AND CHARACTERISTICS 

•  Transportable terrace/garden heater with cylinder housing.  
•  Constructed with aluminium, powder coated and stainless steel 
•  Heat is emitted upwards through the glass tube and distributed via the top 

reflector. 

 

SPECIFICATIONS 

 

•  This heater is best used with propane gas 
•  Max. wattage: 13kw 
•  Min. wattage: 5kw 

 

Gas Consumption 

 

APPLIANCE CATEGORY: 

3+(28-30/37) 

3B/P(30) 

3B/P(50) 

3B/P(37) 

TYPES OF GAS: 

Butane 

Propane 

Butane, propane 
or their mixtures 

Butane, propane 
or their mixtures 

Butane, propane 
or their mixtures 

GAS PRESSURE: 

28-30mbar 

37 mbar 

30 mbar 

50mbar 

37mbar 

OUTLET PRESSURE 
OF REGULATOR: 

 

30mbar 

 

37 mbar 

 

30 mbar 

 

50mbar 

 

37mbar 

 

Use the correct regulator according to outlet pressure of regulator as showed in the table above. 

 

Injector Information 

 

APPLIANCE CATEGORY: 

3+(28-30/37) 

3B/P(30) 

3B/P(50) 

I

I

I

I

I

I

I

I

3B/P(37) 

TYPES OF GAS: 

Butane 

Propane 

Butane, propane 
or their mixtures 

Butane, propane 
or their mixtures 

Butane, propane 
or their mixtures 

GAS PRESSURE: 

28-30mbar 

37 mbar 

30 mbar 

50mbar 

37mbar 

TOTAL HEAT 
INPUT  (Hs): (Qn) 

 

13kW  (945g/h) 

 

INJECTOR SIZE: 

1.88 mm for main burner 
0.18 mm for pilot burner 

1.55 mm for main burner
0.18 mm for pilot burner 

1.65 mm for main burner 
0.18 mm for pilot burner 

The marking

 

for example

 

1.88 on the injector

indicates that the size of injector is 1.88mm 

 


  The hose and regulator assembly must conform to adequate standards. 
  Regulator outlet pressure should meet the corresponding appliance category in 

the Specification section above. The appliance requires approved hose  with a 
minimum length of 0.5

  m. 

  

Summary of Contents for JMC-OSPH-SS











Reviews: