Jiehao INEN-6102 User Manual Download Page 6

Page: 6 / 14

JXDH-6102 User Manual

Chengdu Jiexun Electronics Co.Ltd,

ttp://

WWW.JIE-XUN.COM

-mail

[email protected]

Chapter 2 Installation Guide

2.1 Acquisition Check

When users open the package of the device, it is necessary to check

items according to packing list. Normally it should include the following

items:

JXDH-6102 multiplexer

User’s Manual 1

ASI digital signal input and output wire 8

AC Input Power Cord 1

If any item is missing or mismatch with the list above, please contact

local dealer.

2.2 Installation Preparation

When users install device, please follow the below steps. The details of

installation will be described at the rest part of this chapter. Users can also

refer rear panel chart during the installation.

The main content of this chapter including:

Checking the possible device missing or damage during the

transportation

Preparing relevant environment for installation

Installing Encoder JXDH-6102 Multiplexer

Connecting signal wires

2.2.1 Device’s Installation Flow Chart Illustrated as following

Connecting

Grouding
Wire and

Power

Cord

Acquisition

Check

Fixing

Device

Setting

Parameter

Running

Device

Connecting

Signal Wire

Summary of Contents for INEN-6102















Search results

Summary of Contents for INEN-6102

Reviews:

Related manuals for INEN-6102

Brands by name

Popular brands

Jiehao INEN-6102, User Manual

Search results

Summary of Contents for INEN-6102

Reviews:

Related manuals for INEN-6102

Brands by name

Popular brands