manualshive.com logo in svg

Jiehao INEN-6102, User Manual, Page: 3 / 14

Share
Download
Jiehao INEN-6102 User Manual Download Page 3

JXDH-6102    User  Manual                                                                                        

Chengdu  Jiexun  Electronics  Co.Ltd,

H

ttp://

WWW.JIE-XUN.COM

E

-mail

[email protected]

2

  Have the function of insert and reflection of SDT/NIT

  Able to connect independent scrambler for scrambling to specified program or

service.

  Generating SPI/SI information

  Support PCR adjusting and PID re-reflection

 out put data rate 0-155Mbps,188 byte format

 Each input support 270Mbps data rate, total 8 input rate is 576Mbps

 High precision PCR revise, usually holding 20-60ns

 MPEG2 program delay less than 100 s

 PID filtration/PID redefine function. User can delete, add, revise program even

the program name, PID or serials No. easily.

 Chinese and English LCD display

 Ethernet interface10/100M, long-distance control multiplexer via PC

 Have the function of parameter memory

 Have the function of PSI auto-built.

  High reliability design, stable in running

  Alarm display

  Support network upgrade

1.3 Performance Index

8Routes Standard ASI Interfaces

Input Interface

ASI

Maximum 270Mbps per route
Re-multiplexing MPEG-2 stream
PID re-reflection
PCR reset

Re-multiplexing

Automatically generating PSI/SI table

Output
Interface

ASI

4 routes(2 gyoups separate output)

Summary of Contents for INEN-6102















Reviews:

No comments