JEWELL TuffTilt Digital Manual Download Page 18 | Manualshive

Page: 18 / 43

JEWELL TuffTilt Digital Manual Download Page 18

B-06-1006, Rev. E Tuff Tilt Digital

17

Syntax: *ttssSO-<output format><CR><LF>

Error Strings:

ERR XY-SO BAD PARAMETER

<output format> was invalid.

ERR XY-SO PARSE ERROR

Could not parse <output format>.

Default: SIM

Persistence: Setting is stored in nonvolatile memory.

Example:

command: *9900SO-XDR<CR><LF>

response: <none>

---------------------------------------

XY-MEMS Stores the tiltmeter readings in simple format (SO-SIM) at selected

output rate in nonvolatile memory.

Syntax: *ttssXY-MEMS<CR><LF>

Error Strings: None.

Default: N/A

Persistence: Subsequent tiltmeter readings stored in nonvolatile memory

until memory is full. Maximum of approximately 150 lines of data.

Example:

command: *9900XY-MEMS<CR><LF>

response: <none>

---------------------------------------

XY-MEMD Downloads the tiltmeter readings in nonvolatile memory to PC.

Syntax: *ttssXY-MEMD<CR><LF>

Error Strings: None.

Default: N/A

Persistence: Stored tiltmeter readings downloaded at rate of

1 per second to PC in ASCII comma-delimited string.

Example:

command: *9900XY-MEMD<CR><LF>

response: $start:11-11-1997 18:43:09 4/sec

$000.699,-01.022,025.116,N1028

$000.699,-01.022,025.116,N1028

$000.698,-01.021,025.110,N1028

$000.698,-01.022,025.122,N1028

«
...
16
17
18
19
20
...
»

Summary of Contents for TuffTilt Digital












































Reviews:

No comments