background image

 
 
 
                                                                                                                                                                                                                                                                                                                                                

 
 
 

 

Introduction of 

S755TWIN Motherboard

 

1-1  Feature of motherboard 

The S755TWIN motherboard is design for use 64bit AMD Athlon64 (K8) Processor in 754 
Pin HyperTrnsport Processor with the SiS 755/963L Chipset delivers a high performance and 
professional desktop platform solution. Which utilize the Socket 754 design and the memory 
size expandable to 2.0GB. 

The motherboard  use the newest SiS 755 North bridge chipset supports 800MHz System Bus 
in data transfer rate, and provided 200/166/133MHz SDRAM clock frequency support 
DDR400/DDR333/DDR266 SDRAM. The motherboard embedded SiS 963L south bridgeand 
offers two parallel ULTRA ATA 

133 

interface to provide speedier HDD throughout that 

boosts overall system performance. 

The motherboard integrated SiS 180 Serial-ATA IDE controller provided two Serial-ATA  
port and one Parallel Ultra ATA port (two devices), supports Ultra ATA/Serial ATA, 
Ultra/Serial ATA RAID 0 or 1, Ultra/Serial ATA Raid 0+1 meet future IDE demand increase 
the data transfer rate. 

For those wanting even greater graphic performance, an AGP slot is included on the board 

(For 1.5V AGP card only. No for 3.3V or Universal AGP card).

 This AGP slot will 

support either a 4X/8X VGA card compliant to AGP specification 2.0/3.0    

The motherboard including Fast Ethernet MAC and PHY chip support 10Mb/s, 100Mb/s Base 
transfer rate.  

The motherboard also has an integrated PCI 6-channel Audio chip on board support 6-channel 
3D surround positioning Audio which is fully compatible with Sound Blaster Pro

 that gives 

you the best sound quality and compatibility. The motherboard provided SPDIF-In/ SPDIF-
Out optical function support SPDIF device.    

With USB control as well as capability of expanding to 6 USB2.0 function ports, these 
motherboards meet future USB demand also these motherboard have built-in hardware 
monitor function. This will monitor and protect your computer. These motherboards special 
design in hardware to protect BIOS from virus crash BIOS data.  

These motherboards provide special function in BIOS Setup to setting CPU Host clock step 
by step increasing let users to approach over clocking. 

These motherboards provided high performance & meet future specification demand.  It is 
really wise choice for your computer. 

 

 
 
1-2  Specification 

Summary of Contents for S755TWIN
































































Reviews: