JetStor SAS 712U User Manual Download Page 47

Page: 47 / 119

SAS 712 U Series User Manual

We define that the management port is a special network port. It can download JetCentral

software via HTTP, but it cannot be used as WebDAV service nor linked aggregation with other

LAN ports. In addition, GbE and 10GbE LAN ports cannot link aggregation each other either. The

following table describes the relationship with the service and the network ports.

Service

Management port

LAN1 ~ LANn

HTTP (Download JetCentral page)

Yes

CIFS

Yes

NFS

Yes

AFP

Yes

WebDAV

Yes

iSCSI

Yes

Link aggregation

Yes

This table shows the column descriptions.

Column Name

Description

Name

Management port or LAN ports.

LAG

Link aggregation status.

LAG#

Link aggregation number.

VLAN

VLAN number.

DHCP

Use DHCP , BOOTP or static IP.

Protocol

Use IPv4 or IPv6.

IPv4

IPv4 address.

IPv6

IPv6 address.

Type4

IPv4 address mode:



Static: static address.



DHCP: DHCP assigned address.

Type6

IPv6 address mode:



Static: static address.



Auto: RA (router advertisement” calculated address.



DHCP: DHCPv6 assigned address.

Gateway

Gateway that uses IPv4 address.

Gateway6

Gateway that uses IPv6 address.

MTU

Jumbo frame size

MAC address

Link

Network link status:



Green light: Link up

Summary of Contents for SAS 712U





















































































































Search results

Summary of Contents for SAS 712U

Reviews:

Related manuals for SAS 712U

Brands by name

Popular brands

JetStor SAS 712U, User Manual

Search results

Summary of Contents for SAS 712U

Reviews:

Related manuals for SAS 712U

Brands by name

Popular brands