VAC Controller CVS/VIP
Tel. +47 70 03 91 00
www.jetsgroup.com
Product No. 121315143
Doc. Rev.: 5 (2020-11-30)
3
Important Health and Safety Information
Installation, operation and maintenance must be carried out in strict accordance with this guide and with all applicable regulations. For your own
protection and the protection of others, it is necessary to familiarize yourself with, and always follow, the contained safety and environmental
precautions for our products.
This manual is an integral part of the product/delivery. Always keep it in a safe place for future reference. It is entirely the owner’s responsibility to
ensure that all safety and environmental measures, in accordance with local, state and federal laws are followed. Jets Vacuum AS assumes no
responsibility for equipment damage, personal injury or death and/or delays that result from a lack of respect for the instructions for installation
and/or use as stated in this documentation. Disregarding these instructions may invalidate all warranties.
Safety information references are in accordance with Jets Vacuum AS documentation system. If you do not understand the warnings, stop work
immediately and contact Jets Vacuum AS (citing the safety reference number) for further clarification.
For further information about the included warnings or any other safety concerns please contact Jets Vacuum AS.
Important Health and Safety Warnings
3.1 Warning
All wiring should be performed by a licensed or certified electrician.
3.2 Warning
Never work on the equipment when mains power is applied.
For equipment fitted with a frequency converter: After disconnecting the
input power, always wait for 5 min to let the intermediate circuit
capacitors discharge before you start working on the equipment.
1.2 Warning
Be thoroughly familiar with the controls and the proper use of the equipment
prior to installing, starting or using the equipment. Know the equipment
application, limitations and potential hazards.
3.3 Warning
Avoid kinking and protect electrical cord/s from sharp objects, hot
surfaces, oil and chemicals. Replace or repair damaged or worn cords
immediately. In case of cable damage contact a qualified technician for
replacement.
3.4 Warning
Shoreside applications only: For maximum safety, the equipment should be
connected to a grounded circuit equipped with a ground fault interrupter
device. Before installing the equipment, have the electrical outlet checked by
a licensed or certified electrician to make sure the outlet is properly grounded.
Make sure that grounding conductors are adequately sized as required by
safety regulations.
3.5 Warning
Ensure that the line voltage and frequency of electrical current supply
agrees with the equipment specifications
3.21 Warning
Do not use plugs or connectors that are damaged.
3.24 Warning
Avoid touching the connector with wet hands. Do not disconnect the
plug by pulling the electrical cord
2.14 Warning
The equipment safety is guaranteed only if used in compliance with the
instructions provided. Do not exceed the limits provided.
6.11 Notice
Immediately upon receipt check the equipment for external damage.
Any damage detected after dispatch should be reported immediately to
Jets Vacuum AS and commissioning must be postponed until equipment
has been inspected. Do not dispose of damaged items. Your direct
supplier will advise you of the procedure to follow.
6.3 Notice
Check total quantities of each item against shipping records. Ensure that all
items have been received as per Jets™ order confirmation. Any
discrepancies must be reported to the carrier and to your direct supplier or
Jets Vacuum AS immediately.
6.4 Notice
After unpacking the equipment carefully inspect and tighten any parts,
nuts, bolts or screws that may have become loose in transit.
6.6 Notice
Goods to be protected against shock, falls, dust, foreign matter, grinding,
welding, humidity and moisture.
3.6 Warning
Risk of electric shock. Never connect the green (or green and yellow)
wire to a live terminal.
3.31 Caution
Jets Vacuum AS electrical supply includes cables outfitted with a Shuko 2
pole plugs + PE dependent on equipment specifications. Do not alter this
configuration without authorization from a specialized technician.
Delivery, Receipt of Goods and Transportation
Goods to be protected against shock, dust, humidity and frost. Suitable adequately dimensioned transporting equipment is to be used. Note that
the equipment may contain components that are easily damaged as a result of inappropriate handling. Jets Vacuum AS is not responsible for or
liable for delivery delays resulting from occurrences outside of Jets Vacuum AS' immediate control. On receipt of goods, check for visual damage.
Any damage detected after dispatch should be reported immediately to Jets Vacuum AS. Damages and/or discrepancies must be reported in
writing no later than eight (8) days after receipt of goods. Commissioning must be postponed until the equipment has been inspected. Do not
dispose of damaged items. Your direct supplier will advise you of the procedure to follow.
Storage
Unless otherwise specified, goods are to be stored in a dry environment between 0°C and +40°C prior to installation. The storage location must be
dust free, low humidity (≤95%) and be free from moisture. Keep clear of foreign objects.
Installation to End Use
Site to be a dry environment b0°C and +45°C. The site is to be dust free and protected from grinding and welding. During installation, the
site is to be protected from water, frost and moisture. Goods are to be stored as per the instructions for delivery, storage and transport. A visual
inspection is to be carried out on receipt of goods as well as at the time of installation to ensure that storage and transport conditions after receipt
have not compromised the quality of the product/s.
