JETI model Max BEC 2D Manual Download Page 9

Page: 9 / 12

which point the BEC is now switched-off.

The whole system remembers whether it has been switched-off or modified. If the BEC is

switched-on and the battery is disconnected, then the next time the battery is connected, the BEC

will immediately be switched-on.

For safety and security, the BEC should always be switched-

off via the magnetic switch before disconnecting the battery power.

After connecting the power-supply battery and switching the BEC on via the magnetic switch, the

unit automatically checks the number of connected batteries. The BEC acknowledges a battery

connection if the input voltage on either input exceeds 1 volt. If at any time the input voltage drops

below 1 volt, then an error message 'X input error' is displayed, where X is A or B, to indicate on

which input the problem was detected. The error condition remains until the unit is switched-off

and the battery is disconnected.

Always follow the same procedure when switching on/off. To switch-on, first connect the

batteries and then use the magnetic switch to activate the unit. To switch-off, always use

the magnetic switch to turn-off the unit before disconnecting the batteries.

7. Installation

The BEC can be mounted in your model using the 4 mounting holes on the unit, along with the

rubber-grommets to reduce vibrations. The magnetic switch offers two mounting holes and the

upper-lid (or face-plate) should be used as a mounting template for this part of the unit. The latter

is designed to be mounted on the outside of the unit, being mechanically secured by the screws

included. This allows for easy switching on/off of the BEC and at the same time allows good

visibility of the green and red LED's on the face-plate of the switch.

To ensure safe and reliable operation of your BEC, please ensure an adequate flow of

cooling air to allow the heat-sink to dissipate heat.

8. Safety Precautions For The Manipulation Of Magnets

Since the MAXBEC2D contains magnetic components, it is necessary to follow some simple rules

Summary of Contents for Max BEC 2D












