JessEm Tool Mast-R-Fence Operating Instructions And Parts Manual Download Page 10

Page: 10 / 15

Installing Sub-Fence Offset Track

Fence Model 04010 and Model 04100 are both

equipped with sub-fence off

t tracks. These

offset tracks are designed to be installed two

allow for a 1/32” or 1/16” offset of the sub

Notice the female profile of the extrusion, you will

see that one side of the profile is deeper than the

other side. The small side is 1/32” and the

deeper side is 1/16”.

The sub-fence offset tracks are located on the

backside of the fence in a specially designed

storage location (Fig. 17).

Remove one side of the fence sub-fences by

unscrewing the black knob and removing the

sub-fence bolts (Fig. 18). Once the sub

has been removed, notice the end of the fence

extrusion. The fence extrusion is designed with

mating male profiles designed to accept the

offset tracks (Fig. 19). Side the offset tracks

onto the fence extrusion take care that you install

both offsets on the same side (Fig. 20

offsets should always be installed on the same

side to insure the sub-fence is offset the same

distance at the top and bottom of the sub

Once the offset tracks are securely in place,

reinstall the sub-fence with the sub-

washer , and black locking knob.

Fence Offset Track

Fence Model 04010 and Model 04100 are both

t tracks. These

offset tracks are designed to be installed two

allow for a 1/32” or 1/16” offset of the sub-fence.

female profile of the extrusion, you will

see that one side of the profile is deeper than the

other side. The small side is 1/32” and the

fence offset tracks are located on the

backside of the fence in a specially designed

fences by

unscrewing the black knob and removing the

. Once the sub-fence

has been removed, notice the end of the fence

extrusion. The fence extrusion is designed with

ting male profiles designed to accept the

). Side the offset tracks

onto the fence extrusion take care that you install

ffsets on the same side (Fig. 20). Both

offsets should always be installed on the same

fence is offset the same

distance at the top and bottom of the sub-fence.

Once the offset tracks are securely in place,

-fence bolt,

Figure 18

Figure 19

Figure 20

Summary of Contents for Mast-R-Fence
















Search results

Summary of Contents for Mast-R-Fence

Reviews:

Related manuals for Mast-R-Fence

Brands by name

Popular brands

JessEm Tool Mast-R-Fence, Operating Instructions And Parts Manual

Search results

Summary of Contents for Mast-R-Fence

Reviews:

Related manuals for Mast-R-Fence

Brands by name

Popular brands