background image

9

3-Wire Cable from Power Supply to 3-Wire Cable 

from Cooktop

IMPORTANT: Use the 3-wire cable from power supply where 

local codes permit connecting the frame-ground conductor to 

the neutral (white) junction box wire:

1.  Disconnect power.
2.  Remove junction box cover if present.
3.  Connect the flexible, cable conduit from the cooktop to 

the junction box using UL Listed or CSA Approved conduit 

connector.

4.  Tighten screws on conduit connector, if present.
5.  Connect the two black wires together using the UL Listed 

wire connectors.

6.  Connect the two red wires together using the UL Listed 

wire connectors.

7.  Connect the green or bare and white cooktop cable wires 

to the white (neutral) wire in the junction box using the 

UL Listed wire connectors.

8.  Install junction box cover.
9.  Reconnect power.

Complete Installation

1.  Check that all parts are now installed. If there is an extra 

part, go back through the steps to see which step was 

skipped.

2.  Check that you have all your tools.
3.  Dispose of/recycle all packaging materials.
4.  Use a mild solution of liquid household cleaner and warm 

water to clean cooktop before use. Dry thoroughly with a soft 

cloth. For more information, see the “Cooktop Care” section 

of the Use and Care Guide.

5.  Read the “Cooktop Use” section in the cooktop Use and 

Care Guide.

6.  Reconnect power.
7.  Test the operation of the cooktop: verify that it heats and 

the control light illuminates in the Hi, Med, and Lo positions. 

Press OFF when done.

NOTE: If the cooktop does not work after turning on the power, 

check that a circuit breaker has not tripped or a household fuse 

has not blown. See the “Troubleshooting” section in the Use and 

Care Guide for further information.

If You Need Assistance or Service:

Please reference the “Warranty” section of the Use and Care 

Guide.

B

D

A

E

F

H

G

I

A.  3-wire cable from power supply
B.  Red wires
C.  Green wires
D.  3-wire cable from cooktop
E.  Junction box

F.  Black wire from power supply
G. UL Listed wire connector
H.  Black wires
I.  UL Listed or CSA Approved 

conduit connector

Summary of Contents for JIC4715GS



















Reviews: