Jenn-Air JGW8130DD series Service Manual Download Page 17

Testing Procedures 

 

!

WARNING

 

To avoid risk of electrical shock, personal injury, or death, disconnect power to oven before servicing, unless 
testing requires power. 

© 2004 Maytag Services

 

16022514   Rev. 0 

 

17

 

 

Illustration Component 

Test 

Procedure 

Results 

H1 Controlled 

Oven temperature 
adjustment 

Press 

BAKE 

pad. 

Enter 

550

 on the digit-pad. 

Immediately press and hold 

BAKE

  

pad for 3 seconds. 
 
Oven can be adjusted from -35 to +35 
degrees in 5-degree increments by 
pressing 

AUTOSET

 pad. To avoid 

over adjusting the oven, move 
temperature 5 degrees each time. 
Wait 4 seconds for the data entry timer 
to expire to accept the change. 
Temperature adjustment will be 
retained even through a power failure

.

 

While increasing or decreasing oven 
temperature, this does not affect self-
cleaning temperature. 

H1 Controlled 

Temperature display 

Press and hold 

Cancel

 and 

Bake

 

pads for 3 seconds. 

This mode enables the user to indicate 
F

°

 or C

°

 on the display. 

H1 Controlled 

Clock Display 

Press and hold 

Cancel

 and 

Clock

 

pads for 3 seconds. 

Allows clock to be toggled On or OFF. 

H1 Controlled 

24 Hour Clock 

Press and hold 

Cancel

 and 

Favorite

 

pads for 3 seconds. 

Allows the time on the clock to be 
toggled from 12 hour or 24 hour display. 

H1 Controlled 

Factory Default 

Press and hold 

Cancel

 and 

Keep 

Warm

 pads for 3 seconds. 

Allows the clock to be reset to factory 
settings. 

H1 Controlled 

Twelve hour off 

Control will automatically cancel any 
cooking operation and remove all 
relay drives 12 hours after the last pad 
touch. 

See Sabbath mode to disable. 

H1 Controlled 

Sabbath Mode 

Hold 

CLOCK

 button for 3 seconds to 

activate Sabbath mode. 
 
Hold 

CLOCK

 

for 3 seconds to disable 

Sabbath mode. 

“88:88” will be displayed and flash for 5 
seconds. 
Display will go back to time of day. 
All pad inputs are disabled except for 
CANCEL and CLOCK pads. 
This mode disables the normal 12 hour 
shutoff to allow operation of the bake 
mode for a maximum of 37 hours. 

H1 Controlled 

Child lock out 

Press and hold 

Cancel

 and 

Cook & 

Hold 

pads for 3 seconds. 

“OFF”

 will 

display where the temperature 
normally appears. 

To reactivate the control, press and 
hold 

Cancel

 and 

Cook & Hold 

pads

 

for 3 seconds.  

This is a safety feature that can be used 
to prevent children from accidentally 
programming the oven. It disables the 
electronic oven control. 
 
Child lockout features must be reset after 
a power failure. 

H1 Controlled 

Diagnostic Code 
Display 

Press and hold 

0/Autoset

 pad and 

Power Up

 the unit. 

Cycle through the codes using the 
number pads 1 through 5. 

The last 5 diagnostic codes will be stored 
in the non-volatile memory. 
 
See 

“Description of Error Codes” 

for 

explanation. 

 

Summary of Contents for JGW8130DD series





























































Reviews: