24
OUTDOOR GRILL CARE
Replacing the Igniter Battery
If igniters stop sparking, the battery should be replaced.
1.
Unscrew igniter button cap counterclockwise to remove.
A
B
A. Igniter push button
B. “AA” size battery
2.
Remove battery from the battery compartment.
3.
Replace with a new alkaline “AA” size battery. Install battery with
negative end in first.
4.
Screw igniter button cap clockwise into place.
General Cleaning
IMPORTANT:
Before cleaning, make sure all controls are off and the
grill is cool. Always follow label instructions on cleaning products.
For routine cleaning, wash with soap and water using a soft cloth or
sponge. Rinse with clean water and dry at once with a soft, lint-free cloth
to avoid spots and streaks.
Do not use steel wool to clean the grill, as it will scratch the surface.
To avoid weather damage to finish, use vinyl grill cover. See
“Assistance” section to order.
STAINLESS STEEL
IMPORTANT:
To avoid damage to stainless steel surfaces, do not use
soap-filled scouring pads, abrasive cleaners, cooktop polishing creme,
steel wool, gritty wash cloths or paper towels.
Cleaners should not contain chlorine. Damage may occur.
Food spills should be cleaned as soon as entire grill is cool. Spills may
cause permanent discoloration.
Cleaning Method:
Ŷ
Rub in direction of grain to avoid scratching or damaging the
surface.
Ŷ
Stainless steel cleaner
Ŷ
Liquid detergent or all-purpose cleaner:
Ŷ
Rinse with clean water and dry with soft, lint-free cloth.
Ŷ
Vinegar to remove hard water spots.
Ŷ
Glass cleaner to remove fingerprints.
GRILL GRATES
IMPORTANT:
To avoid damage to grill grates, do not use a steel or
fiber scraper. Immediately after you are finished cooking, loosen food
soil with a brass bristle brush. Turn all burners to HI for 10-15 minutes
with the hood closed to burn off food soil. Turn off all burners, raise the
hood and let grates cool. Use the brass bristle brush to remove ash from
the grill grates.
When completely cool, grill racks can be removed for thorough
cleaning. Clean them with a mild detergent and warm water.
For baked-on soil, prepare a solution of 1 cup (250 mL) ammonia to 1
gal. (3.75 L) water. Soak grates for 20 minutes, then rinse with water and
dry completely.
WARMING SHELF
Cleaning Method:
Ŷ
Liquid detergent or an all-purpose cleaner.
Ŷ
Rinse with clean water and dry with soft, lint-free cloth.
Ŷ
For tough spots or baked-on grease, use a commercial degreaser
designed for stainless steel.
IMPORTANT:
Make sure gas supply is off and all control knobs are in
the Off position.
EXTERIOR
The quality of this material resists most stains and pitting, providing that
the surface is kept clean, polished and covered.
Ŷ
Apply stainless steel polish to all non-cooking areas before first use.
Reapply after each cleaning to avoid permanent damage to surface.
Ŷ
Cleaning should always be followed by rinsing with clean warm
water.
Ŷ
Wipe the surface completely dry with a soft cloth.
Ŷ
For tough spots or baked-on grease, use a commercial degreaser
designed for stainless steel.
INTERIOR
Discoloration of stainless steel on these parts is to be expected, due to
intense heat from the burners. Always rub in the direction of the grain.
Cleaning should always be followed by rinsing with clean, warm water.
Cleaning Method:
Ŷ
Liquid detergent or all-purpose cleaner.
Ŷ
Rinse with clean water and dry completely with a soft, lint-free
cloth.
Ŷ
A heavy-duty scrub sponge can be used with mild cleaning products.
Ŷ
For small, difficult-to-clean areas, use a commercial degreaser
designed for stainless steel.
Summary of Contents for 740-0711
Page 10: ...10 REPLACEMENT PARTS 34b...
