manualshive.com logo in svg

JEI DRILLING & CUTTING SOLUTIONS RAILBEAST RDP-36, Operator'S Manual

Share
Download
JEI DRILLING & CUTTING SOLUTIONS RAILBEAST RDP-36 Operator'S Manual Download Page 9

WWW.JEIUK.COM 

RAILBEAST RDP-36 

This document is protected by copyrights. 

Copying, using, or distributing without permission of Ansa Group Ltd is prohibited.

 

9 

3. STARTUP AND OPERATION 

3.1. Checking the oil level 

Before  starting,  check  the  oil  level  with  the  engine  stopped  and  on  a  level  surface. 

To do this, unscrew the oil filler cap, wipe its dipstick clean, reinsert the cap into the 

neck as shown, but do not screw the cap in, and then remove it again. If the oil level 

marked on the dipstick is below the minimum required, fill the oil to the bottom edge of 

the hole, and then reinstall the cap. The recommended oil is SAE 10W-30 or different 

specified in the Honda GXH50 

Owner’s Manual. Always fill with oil of the same grade 

and manufacturer. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Minimum required oil level 

Maximum allowed 
oil level 

Bottom edge of the hole 

Oil filler cap 
with dipstick 

Summary of Contents for RAILBEAST RDP-36


































Reviews:

No comments

Brands by name

Popular brands

Load more brands