JCM TBV Series Page 31 Training Download

Page: 31 / 40

Part No. 960-100941R_Rev. A

3 1

TBV Transaction Based Validator

JCM® Training Overview

October, 2016

EJECT

RROR

ODES

Reject Error Codes apply to a Banknote or Ticket not being accepted, and are
indicated by the Bezel LED flashing a

GREEN

color in Test Mode (Offline).

Count the number of Flashes between pauses to identify the Error, Causes and
Solutions.

Table 16

TBV Reject Error Codes

Offline

LED Color

Flash

Sequence

Error

Causes and Solutions

Skewed Insertion

A Banknote has been inserted in an incorrect or crooked direction.

[Solution] Clean or adjust the following parts.

[Relative Parts] Centering Mechanism, Rollers.

If the condition is not resolved, change the above related part or parts.

Abnormal

Magnetic

Detection

Magnetic Sensor detected improper levels.

[Solution] Clean the Banknote Path. Check that the Banknote is not
damaged or exhibiting unfit conditions.

[Relative Parts] Magnetic Head

If the condition is not resolved, change the above related part.

Remaining

Banknotes

Returned

While initializing, a Banknote was detected in the Unit.

[Solution] Clean or adjust the following parts.

[Relative Parts] Centering Mechanism, Rollers, Validation Sensors,
Entrance and Exit Sensors

If the condition is not resolved, change the above related part or parts.
Calibrate the Unit.

Magnification

While transporting a Banknote, improper Sensor levels were detected.

[Solution] Clean the Banknote path. Check that the Banknote is not
damaged or exhibiting unfit conditions.

[Relative Parts] Validation Sensor

If the condition is not resolved, change the above related part. Calibrate the
Unit.

Banknote

Transportation

The Sensors detected improper movement of a Banknote or no Banknote.

[Solution] Clean the Rollers and Banknote Path.

[Relative Parts] BNF Assignation Sensor, Entrance Sensors, Centering
Sensor, Validation Sensors, Feed-out Sensor, Box Feed-out Sensor

If the condition is not resolved, change the above related part or parts.
Calibrate the Unit.

UV Sensor

The UV Sensor detected an abnormal Banknote type.

[Solution] Clean and check for foreign material in the Validation area.

[Relative Parts] UV Sensors

If the condition is not resolved, change the above related part or parts.
Calibrate the Unit.

Pattern Error

The Sensors detected an abnormal Banknote type.

[Solution] Check that the Banknote is not damaged or exhibiting unfit
conditions. Clean the Unit.

[Relative Parts] Validation Sensor

If the condition is not resolved, change the above related part. Calibrate the
Unit.

NOTE: In Operational Mode (Online), Reject Errors are not displayed on the
Bezel LED, which remains lit

BLUE

Summary of Contents for TBV Series









































Search results

Summary of Contents for TBV Series

Reviews:

Related manuals for TBV Series

Brands by name

Popular brands

JCM TBV Series, Training

Search results

Summary of Contents for TBV Series

Reviews:

Related manuals for TBV Series

Brands by name

Popular brands