background image

JCB, SO53 3LE
www.JCBDIY.com
Customer Helpline 0333 0143092  

base plate and angle plate (8) 
superposition at the desired angle 
(0, 15, 30, 45) (See I). For other mitre 
angles, rotate to your desired angle 
(use a protractor scale). Following 
one of the above procedures, hold 
the base plate in position and firmly 
tighten the bolts to clamp the base 
plate at that angle. Finally, check the 
angle and ensure the base plate is 
firmly clamped. The angle markings 
on the base plate are accurate for 
most general purposes but it is 
recommended for accurate work to 
set the angle with a protractor and 
make a test cut on other material. 

11. DUST TUBE (See J)

Mount the dust tube (6) into the 
opening of the base plate (7). 
Make sure that the plastic tip of the 
vacuum connection engages into 
the corresponding opening on the 
housing as shown in the figure. 

12. PROTECTION FINGER 

WIRE

The finger wire is located in front of 
the blade holder. Whilst working, it 
will help prevent accidental contact 
with moving blade.

1

3. DUST BLOWER AIR 

HOLE

This is a small aperture located 
underneath the housing just behind 
the blade guide. Ensure this is 
kept clean to allow the air flow to

 

H

8

I

8

7

6

J

Summary of Contents for JS710LE





















Reviews: