background image

JCB, SO53 3LE
www.JCBDIY.com
Customer Helpline 0333 0143092  

L

K

when cutting tight circles or angles

PLUNGE SAWING

Plunge cutting may be used only 
on soft materials such as wood, 
aerated concrete, gypsum plaster 
boards, etc.!
Use only short saw blades.
Place the front edge of the base 
plate on the workpiece and switch 
on. Press the machine firmly against 
the workpiece and plunge the saw 
blade slowly into the workpiece.
As soon as the complete surface 
of the base plate rests on the work 
piece, continue to saw along the 
cutting line. (See K,L)

METAL CUTTING

Use a finer tooth blade for ferrous 
metals and a coarse tooth blade for 
non-ferrous metals. When cutting 
thin sheet metals always clamp 
wood on both sides of the sheet 
to reduce vibration or tearing of 
the sheet metal. Both wood and 
sheet metal must be cut. Do not 
force the cutting blade when cutting 
thin metal or sheet steel as they 
are harder materials and will take 
longer to cut. Excessive blade force 
may reduce the life of the blade or 
damage the motor. To reduce heat 
during metal cutting, add a little 
lubricant along the cutting line..

Summary of Contents for JS710LE





















Reviews: