background image

JCB, SO53 3LE
www.jcb-tools.com
Customer Helpline 0333 0143092  

ENVIRONMENTAL PROTECTION

 

Waste electrical products should not be disposed of with household waste. 
Please recycle where facilities exist. Check with your local authorities or retailer 
for recycling advice.

PLUG REPLACEMENT (UK & IRELAND ONLY)

If you need to replace the fitted plug then follow the instructions below.

IMPORTANT

The wires in the mains lead are colored in accordance with the following code:

Blue – Neutral

Brown – Live

As the colors of the wires in the mains lead of this appliance may not correspond 
with the coloured markings identifying the terminals in your plug, proceed as 
follows. The wire which is coloured blue must be connected to the terminal which 
is marked with N. The wire which is coloured brown must be connected to the 
terminal which is marked with L.

 

Warning:

Never connect live or neutral wires to the earth terminal of the plug. Only fit 

an approved BS1363/A plug and the correct rated fuse.

Note:

 If a moulded plug is fitted and has to be removed take great care in 

disposing of the plug and severed cable, it must be destroyed to prevent 
engaging into a socket.

 

13 Amp fuse approved

to BS1362

Connect

Blue to N

(neutral)

Outer sleeve

firmly clamped

Brown L(live)

Cable grip

Summary of Contents for JCB-SS240





















Reviews: