ENGLISH
OPERATION MANUAL
JB SYSTEMS
®
9/15
USB 1.1 REC
IR-REMOTE CONTROLLER
1. [OPEN/CLOSE]-button:
same functionality as the
[OPEN/CLOSE]-button (24) on the player.
2. [SOURCE]-buttons:
same functionality as the [SOURCE
SELECT]-button (25) on the player.
3. [PLAY-PAUSE/MARK/REC]-buttons:
same functionality as the
[PLAY-PAUSE/MARK/REC]-buttons (10+13+14) on the player.
[MARK]-button sets a marking point in your recording file and
continues recording in a new file.
4. [LOOP]-buttons:
same functionality as the [LOOP
IN/OUT/RELOOP]-buttons (11+12) on the player.
5. [SEARCH]-buttons:
same functionality as the [SEARCH]-buttons
(18) on the player.
6. [TRACK]-buttons:
same functionality as the [TRACK]-knob (16)
on the player with folder switch off.
7. [FOLDER]-buttons:
same functionality as the [TRACK]-knob (16)
on the player with folder switch on.
8. [VOLUME]-buttons:
used to change the output volume.
9. [MUTE]-button:
switches the output volume on/off.
10. [SGL/CTN]-button:
same functionality as the single/continuous
option in the setup menu.
11. [PITCH]-buttons:
with the +/-buttons you can change playback speed, maximum speed change is set
with the [PITCH]-button (20) on the player or with the [PITCH RANGE]-button (13): one of the speed
range LEDs on the player must be lit!
12. [KEY LOCK]-button:
same functionality as the [KEY LOCK]-button (19) on the player.
13. [PITCH RANGE]-button:
press this button to choose a pitch range (4% - 8% - 16%). Press this button
for 2 seconds to disable.
14. [REPEAT]-button:
press this button to activate the repeat function. Two possibilities are available:
•
[REPEAT] DIRECTORY:
when on the display only [REPEAT] is lit, the current directory is repeated.
•
[REPEAT] TRACK:
when on the display both [REPEAT] and [SINGLE] are lit, the current track is
repeated.
15. Battery compartment:
Replace only with CR2025 or equivalent 3V type. Danger of explosion if battery
is incorrectly replaced.
SETUP MENU
To increase flexibility some parameters of the [USB1.1 REC] can be changed in the setup menu.
•
To enter the [SETUP] menu, press the [TIME] button (26) for about 3 seconds.
•
Use the [TRACK] knob (16) to browse the different menu options of the main menu.
•
Press the [TRACK] knob (16) to select the menu option you want to change:
•
Use the [TRACK] knob (16) to change the parameters of the selected menu option.
•
If the menu option has submenus, use the [JOG-WHEEL] (28) to browse these.
•
Press the [TRACK] knob (16) again to return to the main menu.
To save your settings: choose menu option B [(EXIT & SAVE)] and press the [TRACK] knob
1. [SLEEP TIME]:
to extend the lifetime of the laser, the unit goes automatically to sleep mode while not
used for 15 minutes (default). In this menu option you can change, the time it takes to enter sleep mode:
Turn the [TRACK] knob (16) to select the desired time: [No SLEEP]
120 minutes.
Press the [TRACK] knob (16) to save the new value and return to the main menu.
2. [Line Mode]:
you can configure how the text line shows information that is longer than 10 characters.
You can choose 3 different modes + some extra fine-tuning:
There are 3 submenus: push the [TRACK] knob (16) to select a submenu.
o
[Mode = 1]:
text line scrolls and waits for a certain time before scrolling starts again.
Turn the [JOG WHEEL] (28) to select the desired value:
[Dis. = 0.5s
12.0s]:
waiting time in seconds.
[Run = 50ms
2000ms]:
50ms = fast speed / 2000ms = slow speed
o
[Mode = 2]:
text line scrolls only one time, then stops.