42
If you experience any of the following
difficulties while using the system,
use this troubleshooting guide to help
you remedy the problem. Should any
problem persist, consult your
authorized JBL dealer.
No power.
• Is the power cord firmly plugged
into the power outlet?
• One of the safety mechanisms may
be operating. In this event, unplug
the player from the power outlet
briefly and then plug it in again.
No picture.
• Check that the system is connected
correctly and securely.
• The video cable may be damaged.
Replace it with a new one.
• Make sure the system is connected
to a video input on the TV (see page
15).
• Make sure the TV is turned on.
• Make sure the correct video input
on the TV is selected for viewing
with this system.
Noise (interference) appears in the
picture.
• Clean the disc.
• If video from this system has to go
through your VCR to get to your TV,
the copy-protection applied to some
DVD programs could affect picture
quality. If you still experience pro-
blems after checking your connecti-
ons, please try connecting your DVD
system directly to your TV’s S-Video
input, if your TV is equipped with
this input (see page 15).
The aspect ratio of the screen is
wrong (picture vertically expanded)
when you play a wide picture even
though you set “TV DISPLAY” in the
SETUP menu to "WIDE 16:9".
• If you connect the system with the
SCART cable, connect directly to
the TV. Otherwise the autoswitch
function of the aspect ratio for the
TV may not work.
• Depending on the TV, you may not
be able to change the aspect ratio.
In that case (TV not adjustable to
16:9) do not select "WIDE 16:9" in the
TV Display. Then, no change of the
aspect ratio is needed.
There is no sound or volume is very
low
• Check that the speakers and
components are connected
correctly and securely.
• Make sure that you have selected
the correct source on the system.
• Press
MUTE
on the remote control if
the red MUTE LED on the front panel
is blinking.
• The protective circuitry has been
activated because of a short circuit.
Turn off the system, eliminate the
short circuit problem and turn on
the power again.
• The audio interconnect is damaged.
Replace it with a new one.
• The system is in pause mode or in
slow-motion play mode, or fast
forward or fast reverse. Press
/
B
to return to normal play mode.
• Check the speaker settings (see
page 30).
The left and right sounds are
unbalanced or reversed.
• Check that the speakers and
components are connected
correctly and securely.
• Adjust front balance using
SELECT
and
ADJ/VOL +
/
-
(see page 41).
Severe hum or noise is heard.
• Check that the speakers and
components are connected
securely.
• Check that the connecting cords are
away from a transformer or motor
and at least 3 meters away from
fluorescent light.
• Move your TV away from the audio
components.
• The plugs and jacks are dirty. Wipe
them with a cloth slightly moistened
with alcohol.
• Clean the disc.
The surround effect is difficult to
hear when you are playing a Dolby
Digital sound track.
• Check to see if the Dolby Digital
mode is turned on properly (red
"Dolby Digital" indicator lights in the
front panel), otherwise unload and
load the disc again.
• Check the speaker connections.
• Depending on the DVD disc, the
output signal may at times be mono
or stereo even if the soundtrack is
recorded in Dolby Digital format.
The sound comes from the center
speaker only.
• Depending on the disc, sound may
sometimes come from the center
speaker only. This also applies to
mono recordings (from disc or any
analog source), when Pro Logic or 3
Stereo mode is selected. This is
normal.
No sound is heard from the center
speaker.
• Do not set listening mode to Dolby
Pro Logic Phantom (see page 36).
• Adjust center speaker volume (see
pages 40).
No sound or only very low volume
from the rear speakers.
• Do not set listening mode to
3-Stereo (see page 36).
• Adjust the rear speaker volume (see
page 40).
Radio stations cannot be tuned in.
• Check that the antennas are
connected correctly. Adjust the
antennas and connect an external
antenna if necessary.
• The signal strength of the stations is
too weak for automatic tuning. Use
manual tuning.
• No stations have been preset.
• The tuner mode is not selected,
select the Tuner mode.
T R O U B L E S H O O T I N G
