JB Systems LOUNGE LASER Operation Manual Download Page 4

Page: 4 / 17

ENGLISH

OPERATION MANUAL

JB SYSTEMS

3/29

LOUNGE LASER

country to country. The user must always inform himself on the legal instructions valid in his country and
apply them to his situation.

Please note that

JB SYSTEMS

cannot be made liable for damages caused by incorrect installations and

unskilled operation!

DESCRIPTION:

1. MAINS INPUT:

connect the supplied power supply here

2. KEY ACTIVATED SWITCH:

used to switch the lasers on/off. Use the keys to make sure only a skilled

operator is able to switch the laser on.

3. ON/OFF SWITCH:

used to switch the unit on/off.

4. LASER ROTATION SWITCH:

used to reverse the rotation of the laser effect

5. LASER ROTATION SPEED KNOB:

used to set the rotation speed of the laser effect

6. RED STROBE:

used to adjust the flashing time of the red laser

7. GREEN STROBE:

used to adjust the flashing time of the green laser

8. LED EFFECT ROTATION SWITCH:

used to reverse the rotation of the led effect

9. LED EFFECT ROTATION SPEED KNOB:

used to set the rotation speed of the led effect

10. DIMMER:

used to adjust the dimming level of the led effect

11. HANGING BRACKET:

with 2 knobs on the sides to fasten the unit and a mounting hole to fix a

mounting hook.

OVERHEAD RIGGING



Important: The installation must be carried out by qualified service personal only. Improper
installation can result in serious injuries and/or damage to property. Overhead rigging requires
extensive experience! Working load limits should be respected, certified installation materials
should be used, the installed device should be inspected regularly for safety.



Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging
and servicing.



Locate the fixture in a well ventilated spot, far away from any flammable materials and/or liquids. The
fixture must be fixed

at least 50cm

from surrounding walls.



The device should be installed out of reach of people and outside areas where persons may walk by or be
seated.



Before rigging make sure that the installation area can hold a minimum point load of 10times the device’s
weight.



Always use a certified safety cable that can hold 12times the weight of the device when installing the unit.
This secondary safety attachment should be installed in a way that no part of the installation can drop
more than 20cm if the main attachment fails.



The device should be well fixed; a free-swinging mounting is dangerous and may not be considered!



Don’t cover any ventilation openings as this may result in overheating.

ENGLISH

OPERATION MANUAL

JB SYSTEMS

4/29

LOUNGE LASER



The operator has to make sure that the safety-relating and machine-technical installations are approved by
an expert before using them for the first time. The installations should be inspected every year by a skilled
person to be sure that safety is still optimal.

OPERATING INSTRUCTIONS

CAUTION EYEDAMAGE:

Always position the laser in a way that prevents the

audience from looking directly into the laser beams. The installation should assure that
the beam will not strike the audience.

MAINTENANCE



Make sure the area below the installation place is free from unwanted persons during servicing.



Switch off the unit, unplug the mains cable and wait until the unit has been cooled down.

During inspection the following points should be checked:



All screws used for installing the device and any of its parts should be tightly fastened and may not be
corroded.



Housings, fixations and installations spots (ceiling, truss, suspensions) should be totally free from any
deformation.



When an optical lens is visibly damaged due to cracks or deep scratches, it must be replaced.



The mains cables must be in impeccable condition and should be replaced immediately when even a
small problem is detected.



In order to protect the device from overheat the cooling fans (if any) and ventilation openings should be
cleaned monthly.



The interior of the device should be cleaned annually using a vacuum cleaner or air-jet.



The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp,
smoky or particularly dirty surroundings can cause greater accumulation of dirt on the unit’s optics.



Clean with a soft cloth using normal glass cleaning products.



Always dry the parts carefully.



Clean the external optics at least once every 30 days.



Clean the internal optics at least every 90 days.

Attention: We strongly recommend internal cleaning to be carried out by qualified personnel!

SPECIFICATIONS

Mains Input:

AC/DC Adapter 230Vac