ENGLISH
03
EN
inStallatiOn
- Choose the mounting location where the unit will not inter
fere with the normal driving function of the driver.
- Before finally installing the unit, connect the wiring tempo
rarily and make sure it is all connected up properly and the
unit and the system work properly.
- Use only the parts included with the unit to ensure proper
installation. The use of unauthorized parts can cause mal-
functions.
- Consult with your nearest dealer if installation requires the
drilling of holes or other modifications of the vehicle.
- Install the unit where it does not get in the driver’s way and
cannot injure the passenger if there is a sudden stop, like
an emergency stop.
- If installation angle exceeds 30°from horizontal, the unit
might not give its optimum performance.
- Avoid installing the unit where it would be subject to high
temperature, such as from direct sunlight, or from hot air,
from the heater, or where it would be subject to dust, dirt or
excessive vibration.
Din FrOnt/rear-MOunt
This unit can be properly installed either from “Front”
(conventional DIN Front-mount) or “Rear” (DIN Rear-
mount installation, utilizing threaded screw holes at
the sides of the unit chassis). For details, refer to
thefollowing illustrated installation methods.
taKe Out SCreW BeFOre inStal-
latiOn (G7 model only)
Before install the unit, please remove the two screws.
Din FrOnt-MOunt (Method a)
Installation Opening
This unit can be installed in any dashboard having
an opening as shown below:
Installing the unit
1. Make sure the ignition is turned off, and then disconnect the
cable from the vehicle battery’s negative (-) terminal.
2. Disconnect the wire harness and the antenna.
3. Press the release button on the front panel and remove the con
trol panel (see the steps of “to detach the front panel”).
4. Lift the top of the outer trim ring then pull it out to remove it.
5. The two supplied keys release tabs inside the unit’s sleeve so
you can remove it. Insert the keys as far as they will go (with the
notches facing up) into the appropriate slots at the middle left
and right sides of the unit. Then slide the sleeve off the back
of the unit.
6. Mount the sleeve by inserting the sleeve into the opening of
the dashboard and bend open the tabs located around the
sleeve with a screwdriver. Not all tabs will be able to make
contact, so examine which ones will be most effective. Bend-
ing open the appropriate tabs behind the dashboard to secure
the sleeve in place.
7. Reconnect the wire harness and the antenna and be careful not
to pinch any wires or cables.
8. Slide the unit into the sleeve until it locks into place.
9. To further secure the unit, use the supplied metal strap to secure
the back of the unit in place. Use the supplied hardware (Hex
30
Take out screw
before installation.
(1) Front Panel (2) Outer Trim Ring(3) Sleeve (4) L key (5) R key
Summary of Contents for G5BT
