![background image](http://html1.mh-extra.com/html/jayco/recon-zx-2011/recon-zx-2011_owners-manual_3682303076.webp)
SECTION 10
SLIDEOUT SYSTEMS
72
After the slideout is
extended, verify that the
corners of the black
rubber seal are set up
correctly. The corners of
this seal are cut at a 45°
angle. The top of the seal
must overlap the side of
the seal to avoid the
possibility of water
penetration.
If the slideout is extended, refer to the
following section on overriding the specific
slideout system installed on your RV.
If the slideout is retracted, leave it in that
position.
Contact your dealer or Jayco Customer
Service for repair assistance.
Fig. 10.4 Exterior
slideout room
corner
If the slideout extends crooked or only one
side moves, follow these steps.
Follow steps on overriding the specific
slideout system installed on your RV.
Retracting slideout room
Press the IN section of the slideout control
switch and hold it until the motor stops.
Operating the switch after the room is fully
retracted will damage the switch and motor.
You may need to push the side that is not
sliding to get it to retract all the way.
Contact your dealer or Jayco Customer
Service for repair assistance.
Maintenance
Dexter Chassis Group (DCG) Center Drive
Slide override
Your slideout system has been designed to
require very little maintenance. To ensure a
long life of your slideout system, read,
understand and follow these simple
instructions. This system contains a pre-lubed
bearing that is lubricated when the room is
moved in and out. Do not spray oil or grease
on the rails while the room is extended.
T
ROUBLESHOOTING
T
HE
S
LIDEOUT
If the slideout does not move when the
slideout switch is depressed, follow these
steps.
Check the auxiliary battery (customer
supplied) for a full charge and good wire
connections.
Check the 12-volt fuse or circuit breaker.
Check for loose connections at the
slideout motor.
If the slideout still will not operate, follow
these steps.
Disconnect the
slideout motor
brake wires from
the power wires.
Connect a 9 volt
battery harness
to the motor
brake wires
Locate the
manual advance
crank nut on the
backside of the motor. Crank the nut on the
slideout motor with a 5/8” socket. With the 9
volt battery connected to the motor brake
crank the nut on the motor until the room is
sealed. Once the slide is in a closed position
remove the 9 volt battery and harness.
V-tech slideout override
If the RV has an
underbelly, locate and
remove the access panel
to access the slideout
motor (this panel is
typically under the RV on
the opposite side of the
slideout room). Use a 3/4
socket and ratchet on the
hex head located on the end of the drive
shaft. Turn the drive shaft until the slideout is
in the position you desire. Contact your RV
dealer for service.
Do not work on your system unless the 12-
volt DC (auxiliary battery, customer
supplied) and 120-volt AC electrical
systems (shore line power cord) have been
disconnected.
Fig. 10.5 DCG manual advance
crank nut
Fig. 10.6 V-tech
slide hex head
Summary of Contents for Recon ZX 2011
