Javelin J205 User Manual Download Page 41

Page: 41 / 43

Quick Start

Getting

Started

Operation

Starting to

Print Cards

Cleaning

Trouble

Shooting

Technical

Specifications

General

Information

Rev. 1.5

Appendix D

Technical Support

If for any reason you require product technical support, please contact the

distributor where you purchased your equipment. If they cannot help you, or at

their direction, contact NBS.

Web: www.nbstech.com

HOW TO RETURN YOUR PRINTER

If you have purchased your printer from an NBS distributor, please first contact

them on their return procedures.

Alternatively, contact the appropriate NBS Technical Support Department (details

above) for instructions before shipping your printer.

For Support in Europe, Middle East,

Africa and Asia Pacific

NBS Technologies

7 Byfleet Technical Centre

Canada Road

West Byfleet

Surrey KT14 7NB

United Kingdom

Tel: +44 1932 351531

Fax: +44 1932 351382

Email: [email protected].

For Support in North and

South America

NBS Technologies

10925 Bren Road East

Minneapolis MN 55343

United States of America

Tel:

1 800 524 0419 or

+1 416 840 8620

Fax: +1 952 912 9439

Email:

[email protected]

Only complete goods in their original packaging with a valid

Returned Materials Advice (RMA)

number clearly

marked on the outside can be accepted for return to NBS.

APPENDIX D

Quick Start

Getting

Started

Operation

Starting to

Print Cards

Cleaning

Trouble

Shooting

Technical

Specifications

General

Information

Summary of Contents for J205












































Search results

Summary of Contents for J205

Reviews:

Related manuals for J205

Brands by name

Popular brands

Javelin J205, User Manual

Search results

Summary of Contents for J205

Reviews:

Related manuals for J205

Brands by name

Popular brands