Javelin J205 User Manual Download Page 40

Page: 40 / 43

Quick Start

Getting

Started

Operation

Starting to

Print Cards

Cleaning

Trouble

Shooting

Technical

Specifications

General

Information

Rev. 1.5

SPARE PARTS

All parts, maintenance kits, options kits, and accessories are warranted to be free

of defects in material and workmanship. This warranty becomes void if the item is

modified, improperly installed or used, or damaged by accident or neglect.

Notes

Failure to exercise caution to protect the equipment from electrostatic discharge

damage, adverse temperature and humidity conditions or physical abuse, including,

but not limited to, improper packaging, shipping, service or repairs performed by

personnel not authorised by NBS or an authorised dealer may void the warranty.

NBS or its authorised dealer will, at its option, repair or replace the equipment or

any parts which are determined to be defective within this warranty period, and

which are returned to NBS or its authorised dealer.

NBS specifically disclaims the implied warranties of merchantability and fitness for

a particular purpose.

For full warranty terms, please contact the Javelin dealer from whom you

purchased your printer.

APPENDIX C

Quick Start

Getting

Started

Operation

Starting to

Print Cards

Cleaning

Trouble

Shooting

Technical

Specifications

General

Information

Summary of Contents for J205












































Search results

Summary of Contents for J205

Reviews:

Related manuals for J205

Brands by name

Popular brands

Javelin J205, User Manual

Search results

Summary of Contents for J205

Reviews:

Related manuals for J205

Brands by name

Popular brands