manualshive.com logo in svg

Javelin J205, User Manual, Page: 30 / 43

Share
Download
Javelin J205 User Manual Download Page 30

23

Rev. 1.5

TECHNICAL SPECIFICATIONS

General

●

High speed printing. 30 seconds per card in  YMCKO 

4 seconds per card in monochrome

●

Small footprint

●

Windows Drivers for 98/2000/ME/XP and NT 4.0 

Colour Printing

●

Colour dye sublimation or monochrome thermal 

transfer printing

●

300 dpi (11.8 dots/mm) print resolution

●

Edge to edge printing standard (J210 only)

●

30 seconds per card edge to edge in full colour (YMCKO)

Bar Codes

●

Code 39

●

Code 128 B & C with & without check digit

●

2 of 5 & 2 of 5 interleave

●

UPCA

●

EAN8 & EAN13

Fonts

●

Resident: Arial Normal 100, Arial Bold 100

●

Flash memory supports download of different fonts.

●

True Type fonts available via Windows driver

Cards

●

Types PVC, Composite

●

Card width/length: ISO CR-80 - ISO 7810,

2.125” (54mm) by 3.375” (86mm)

●

Option: magnetic stripe - ISO 7811

●

Card  thickness: 30mil (0.75mm) 

●

Card feeder capacity: up to 30 cards 

●

Card output hopper capacity: 10 cards 

6

Technical
specifications

Quick Start

Getting

Started

Operation

Starting to

Print Cards

Cleaning

Trouble

Shooting

Technical

Specifications

General

Information

Summary of Contents for J205












































Reviews:

No comments