background image

Jason International, Inc.  •  

 

501.771.4477  

    

Page 10 of 24

 

   

Customer Service :  800.255.5766 

Copyright © 2013 Jason International.

INSTALLATION INSTRUCTIONS (cont.)

Figure 13b

4.  Place the equipment inside the frame and attach 

all the plumbing and electrical connections. See 
Figure 14a for AirMasseur

®

 and 14b for MicroSilk

®

 

baths. 

 

Note: The electrical service can be provided inside 
or outside the enclosure. Refer to the ELECTRICAL 
section of this manual for service requirements. If the 
service is outside the cabinet, position cord through the 
slot provided in the frame and enclosure.

5.  For MicroSilk baths, clamp the plumbing lines to 

the appropriate barb using the clamp provided. 
Assure the line will allow proper drainage to the bath 
fitting.  The hose must have a continuous drop from the 
barb to the fitting. See Figure 14c.

Figure 14b

Figure 14c

6.  Refer to faucet manufacturer’s installation instruc-

tions if a faucet is intended to be mounted on the top of 
the cabinet and position the plumbing stub outs inside 
the cabinet. 

 

Caution: Use long enough stainless steel flexible 
hose to lift the enclosure up to provide access 
for disassembly in the future. Be sure to install a 
faucet that will reach the well of the bath from the 
enclosure. Refer to the bath specification sheet for 
deck width dimensions.

7.  Fill the bath and test all connections for leaks.

8.  Place cabinet on the frame and attach with the four (4) 

screws and decorative caps.

Figure 14a

Summary of Contents for forma AirMasseur RE630PS

























Reviews: