Jasic Cut 160 Operator'S Manual Download | Manualshive

Page: 20 / 32

background image

20

PLASMA TORCH CONSUMABLE BREAKDOWN

The Jasic Cut 160 is supplied with the 6m P150LT plasma torch

Please Note:

The Jasic Cut 160 has an output current rating of 160amps and the supplied plasma torch is the P150LT
which has a current rating of 150amps, this torch is supplied from new with the 150amp tip fitted.
When ordering replacement cutting tips please take note that the maximum sized tip to be used would be
the 150amp 1.8 cutting tip. Using a higher rated tip will give you poor cut performance!

«
...
18
19
20
21
22
...
»

Summary of Contents for Cut 160

































Reviews:

No comments

Related manuals for Cut 160

Brand: Happ Pages: 49

Brand: JBL Pages: 2

Brand: Magnadyne Pages: 20

SET-2000 Oil/Sludge

Brand: Labkotec Pages: 14

Brand: Yamaha Pages: 67

Brand: Yealink Pages: 8

Brand: Face Pages: 12

Brand: Vizio Pages: 20

Brand: R-Tech Pages: 20

DRINKWORKS Home Bar Classic

Brand: Keurig Pages: 32

Brand: HySecurity Pages: 8

Brand: M2M Pages: 7

AC AUTO STOP GEN 2

Brand: Lift Tech Marine Pages: 2

Enforcer SM-407-5T

Brand: SECO-LARM Pages: 1

Brand: NAIM Pages: 31

WELDSKILL 200HF

Brand: CIGWELD Pages: 60

2-way Full Loudspeaker System UB42

Brand: EAW Pages: 2

HOBBY WELD K1790-1

Brand: Lincoln Electric Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands