background image

5 - 20 

emPC-X

 (

Hardware Manual

)  

  Maintenance

 

 
© 

Janz Tec AG

 

Rev. 1.2 

 

 

 

5.2 

Battery Replacement 

 

 

CAUTION : Fire Risk 

 The installed computer board is equipped with a Lithium battery. 
Danger  of  explosion  if  battery  is  incorrectly  replaced.  Replace  only  with  battery  of  the 
same or equivalent type (3-volt lithium coin cell battery). 

 

Do not attempt to recharge the battery. 

 

Do not disassemble, crush, puncture, short external contacts, or dispose of in fire 
or water.

 

 

 

NOTICE: Battery approval 

 The battery must be a compatible battery type: CR2032 (3 Volt lithium coin cell battery). 
The replacement battery must have a NRTL approval. 
 

 
Compatible battery type for products with extended temperature specifications: CR2032 (3 Volt lithium 
coin cell battery) with temperature range -40 .. +85°C or better (Recommended: Murata CR2032X or 
CR2032W). 
 
The battery is used for backing up the system time when the power supply is removed. 
 

1.  Turn  off  the  computer  properly  through  the  operating  system,  then  turn  off  any  external 

devices. 

2.  Disconnect the power supply from the power inlet and disconnect any external devices. 
3.  Disassemble the housing and locate the battery on the power supply board 
4.  Remove the battery from the holder (See figure 11) 
5.  Insert the new battery (See figure 11) 
6.  Reassemble the housing 

 

 
 

 

1

2

 

 

1.  Removal: Insert screwdriver at right side and bend so that the battery 

pops outs. Use only gentle force, otherwise the battery holder might 
be damaged. 
The use a plastic tool is preferred to avoid shorting the battery 

2.  Insertion: Align new battery to the left side of the holder and gently 

press down on the right side of the battery until the battery snaps into 
the holder. 

 

figure 11: Removing and replacing coin cell battery 

Summary of Contents for emPC-X Series




























Reviews: