Janus Remote Communications POTSwap LTE910PS Product User Manual Download | Manualshive

Page: 16 / 17

background image

LTE910PS v1.00 User Manual JA16-UM

Page 16 Rev: 00 Date: 07/24/19

© Copyright 2019 Janus Remote Communications

Specifications subject to change without notice

All Rights Reserved See website for latest revision. Not intended for life support applications.

9. Compatible Terminal Block Connectors

The POTSwap has a 0.200” terminal block header, also referred to as a 5.08 mm Eurostyle connector. It supports a
variety of plug-in terminal block types, including screw terminal, spring contact and crimp terminals.

Manufactures for these terminal blocks include:

•  Camden Electronics
•  FCI Electronics
•  Molex
•  OST (On Shore Technology)
•  Phoenix Contact
•  TE Connectivity (Tyco/Buchannan)
•  Weidmüller
•  Würth Elektronik

Below is a small sample of compatible connectors:

TYPE

MANUFACTURER

PART NO.

DESCRIPTION

Screw Terminal

TE Connectivity

1

796634-2

vertical screw, horizontal plug

TE Connectivity

1986484-2

horizontal screw, vertical plug

Molex

395300002

vertical screw, horizontal plug

Molex

395332002

horizontal screw, vertical plug

Weidmuller

1943580000

vertical screw, horizontal plug

Spring Clamp

Weidmuller

1013680000

orange

Weidmuller

1013430000

black

Crimp Housing & Contacts

TE Connectivity

1986160-2

crimp housing, green

TE Connectivity

965901-1

crimp terminal, 20-17 AWG

TE Connectivity

965899-1

crimp terminal, 13-17 AWG

Weidmuller

1610490000

crimp housing, orange

Weidmuller

1711960000

crimp housing, black

Weidmuller

1604250000

crimp contact, 24-22 AWG

Weidmuller

1567060000

crimp contact, 20-17 AWG

Weidmuller

1567070000

crimp contact, 16-14 AWG

Note:
1 - This component is available from Janus Remote Communications. See ‘TERMINAL BLOCK’ in Section 10.

«
...
14
15
16
17
»

Summary of Contents for POTSwap LTE910PS


















Reviews:

No comments

Related manuals for POTSwap LTE910PS

Brand: jablotron Pages: 2

Yealink SIP-T22P

Brand: Yealink Pages: 2

Brand: Yealink Pages: 3

Brand: Uniden Pages: 27

Brand: Panasonic Pages: 96

Brand: Panasonic Pages: 8

Brand: GE Pages: 60

Brand: Uniden Pages: 68

Brand: ION Pages: 48

Brand: Tablee Pages: 4

HTVZD*1C series

Brand: Halsey Taylor Pages: 7

Brand: Coby Pages: 1

Brand: VTech Pages: 1

Brand: Uniden Pages: 72

Sailor System 5000 MF/HF

Brand: Sailor Pages: 56

Brand: ETS Pages: 2

Brand: König Electronic Pages: 56

Brand: Harman Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands