Janus Remote Communications POTSwap LTE910PS Product User Manual Download

Page: 13 / 17

LTE910PS v1.00 User Manual JA16-UM

Page 13 Rev: 00 Date: 07/24/19

Specifications subject to change without notice

6. SIM Card Installation

The POTSwap requires the installation of an activated SIM card for operation. A ‘micro’ (3FF) size SIM card is
required.

The SIM card holder is mounted to a p.c.board behind the slot, so some care is required to insure that the SIM
card is inserted correctly. It should not take much effort to insert the SIM card if properly aligned.

Do NOT force the SIM card into the slot. Do not insert tools, paperclips, etc. into the slot.

Insert the SIM card into the SIM slot with the following orientation:

- gold contact side facing down

- narrow edge with chamfered corner in first.

Do NOT use a SIM card adaper to install nano sized SIMs into the POTSwap. The adapter edge
can catch on the SIM socket and cause permanent damage.

Summary of Contents for POTSwap LTE910PS


















Search results

Summary of Contents for POTSwap LTE910PS

Reviews:

Related manuals for POTSwap LTE910PS

Brands by name

Popular brands

Janus Remote Communications POTSwap LTE910PS, Product User Manual

Search results

Summary of Contents for POTSwap LTE910PS

Reviews:

Related manuals for POTSwap LTE910PS

Brands by name

Popular brands