JANUS INTERNATIONAL ASTA AMERICA 700 Series Installation Manua Download Page 12

Page: 12 / 12

FIGURE A-1

3- 1/4 X 1-1/4
CARRIAGE BOLT

1/4" X 1/4" X 1" KEYSTOCK

NUTS &
LOCK WASHER

3-BOLT
AWNING CRANK

BRONZE
BEVELED
GEAR

Installing Awning Crank Assembly To

DRIVE SIDE
HEADPLATE

Drive Side Headplate and Shaft

PAGE A-1

ASTA AMERICA

Appendix "A"

Procedure for Installing (optional) Awning Crank

Insert 1/4" x 1" key stock into key seat on drive shaft.

Align bevel gear key way with key stock and slide awning crank onto drive shaft until awning

crank back is seated against head plate.

Align mounting holes in awning crank with mounting holes in head plate. Insert (3) 1/4" x 1-1/4"

carriage bolts from inner side of head plate through holes in head plate and awning crank.

Using the (3) supplied 1/4" lock washers and hex nuts securely tighten nuts to attach awing crank

to head plate.

638 Cassville White Rd NW
Cartersville, GA 30121

P.O. Box 639
Cassville, GA 30123

Office: 770-974-2600

Fax: 770-974-1455
www.astadoor.com

Summary of Contents for ASTA AMERICA 700 Series













Search results

Summary of Contents for ASTA AMERICA 700 Series

Reviews:

Related manuals for ASTA AMERICA 700 Series

Brands by name

Popular brands

JANUS INTERNATIONAL ASTA AMERICA 700 Series, Installation Manua

Search results

Summary of Contents for ASTA AMERICA 700 Series

Reviews:

Related manuals for ASTA AMERICA 700 Series

Brands by name

Popular brands