11
ON/
OFF
Auto.
Perm.
H 1
H 2
Mode
V1
V2
V3
< >
N
ON/
OFF
Auto.
Perm.
H 1
H 2
Mode
V1
V2
V3
< >
N
SELECTRONIC- A
SELECTRONIC A Controller
The machines of the FM 128 K
series are equipped as standard
with a Selectronic A controller.
Keypad explanation:
1…………. On/Off button – the LED is lit when in the switched on state.
2…………. Button for Automatic or Permanent operation – pressing the button repeatedly
allows the operator to switch back and forth between Automatic (Auto.) and
Permanent (Perm.). The machine must be in the Off mode (LED for button 1 not lit).
3…………. Button for the heater – pressing the button repeatedly
allows the operator to switch the heater on or off at Level I or Level II.
- If the LED (H1) is lit, heater level I is active.
- If the LED (H2) is lit, heater level II is active.
- If neither LED or both LEDs are lit, the heater is off.
4…………. The Mode button is used to select up to 5 menu items
(see the note to the right in this regard). The selected menu items (5,6,7,8,9)
are lit respectively below.
5…………. When this LED (V1) is lit, you can read out the speed of the pattern roller on the
lower display (11) or use the arrow buttons to the left and right (10, 12) of the
display to change it.
6…………. When this LED (V2) is lit, you can read out the speed of the upper conveyor belt
on the lower display (11) or use the arrow buttons (10, 12) to the left and right
of the display to change it.
7…………. When this LED (V
3
) is lit, you can read out the speed of the sheet transport
on the lower display (11) or use the arrow buttons (10, 12) to the left and right
of the display to change it.
8…………. When this LED (< >) is lit, you can read out the spacing of the shapes which are
placed on the sheet on the lower display (11) or use the arrow buttons (10, 12) to
the left and right of the display to change the spacing or simply decrease it.
9…………. When this LED (N) is lit, you can read out the number of rows of shapes on
the baking sheet on the lower display (11) or use the arrow buttons (10, 12)
to the left and right of the display to change it.
10/11/12…. Values can be read out on the display (11) or they can be changed using the arrow
buttons (10, 12) to the left and right of the display.
13………… the hopper symbol with the associated LED (13) indicates, whether
the safety switches are closed correctly. When the LED is lit, then either
E1 or E2 is shown on the display:
E1 = The emergency stop button is active or is being pressed.
E2 = The hopper is not closed.
E0 = Communication error (this error message should usually disappear
again after 5-10 seconds. If it does not, please call customer
service: +49 2151 24315).
ON/
OFF
Auto.
Perm .
H 1
H 2
Mode
V
1
V
2
V
3
< >
N
ON/
OFF
Auto.
Perm .
H 1
H 2
Mode
V
1
V
2
V
3
< >
N
SELECTRONIC- A
13
12
1
5*
6*
7
8
9
10
11
4
2
3
*) Note:
5*:
The V
1
speed
change of the
pattern roller is
only available if
the machine is
equipped with a
variable motor.
6*:
The V
2
speed
change of the
upper conveyor
belt is only
available if the
machine is
equipped with an
upper conveyor
belt adjuster.