background image

Page 21

4.3  Selecting Model Size

Model PureLink700

Model PureLink1400

Chlorine Production

Chlorine Production

283 gm (0.625 lbs) per 24 Hour period.

567 gm (1.25 lbs) per 24 Hour period.

Residential Pools

Residential Pools

One (1) unit per 57 m

3

 (up to 15,000 gal) pool

 

(year round use).

One (1) unit per 114 m

3

 (up to 30,000 gal) pool

 

(year round use).

One (1) unit per 66 m

3

 (up to 17,500 gal) pool

 

(winterized).

One (1) unit per 132 m

3

 (up to 35,000 gal) pool

 

(winterized).

Commercial Pools

Commercial Pools

Check With Manufacturer. 

See Commercial Sizing Guide.

Check With Manufacturer. 

See Commercial Sizing Guide.

4.4  Chemistry You Need to Know

1. 

Chlorine Stabilizer 

(cyanuric acid) is needed to maintain proper levels of chlorine.  Most unstable 

chlorine is destroyed by the UV radiation from the sun within 2 hours.  Chlorine stabilizer should be 

maintained between 50 - 75 PPM.  See Table 3.

2. 

Nitrates

 can cause extremely high chlorine demands and will deplete chlorine from your swimming 

pool.  In some cases Nitrates may even lower your chlorine levels to zero.  Your local pool professional 

can test for Nitrates.  Make sure Nitrates are not present in your pool.

3. 

Metals 

(some metals) can cause loss of chlorine.  Also, metals can stain your pool.  Have your local 

pool professional check for metals and recommend methods of removal.

4. 

Chloramines

 should not be present in pool water.  When organic materials combine with Free 

Chlorine, Chloramines are formed.  This ties up the Free Chlorine in your pool and does not allow 

the chlorine in your pool to disinfect.  Chloramines also cloud pool water and burn the eyes.  (Super 

Chlorinate (shock) to remove Chloramines at the initial startup of the pool).

5.  

Super Chlorination

 (Shocking) burns out the organic material that has combined with chlorine.  

This frees the chlorine for sanitizing.  This is accomplished by raising the chlorine level quickly and 

dramatically.  When the chlorine level is raised to 5 - 15 PPM the pool water is said to have been Super 

Chlorinated (shocked).  As pool water is continuously passed through the AquaPure Electrolytic Cell, 

all pool water inside the cell is being Super Chlorinated.  When the AquaPure is used on pools the pool 

water sparkles and does not burn the eyes because of the absence of Chloramines.

NOTE

   On initial startup of a pool, it is best to Super Chlorinate from an outside source, i.e., use a shock treatment 

available at your local pool supplier.

6. 

pH

 produced by the AquaPure is close to Neutral pH.  However, other factors usually cause the pH 

of the pool water to rise.  Therefore, the pH in a pool chlorinated by the AquaPure tends to stabilize 

at approximately 7.8.  This is within NSPI standards.  If the pool pH rises above 7.8 have a pool 

professional test to see if other factors such as high Calcium Hardness or Total Alkalinity are the cause 

and then balance accordingly.  

  CAUTION

Never use dry acid to adjust pH in arid geographic areas with excessive evaporation and minimal 

dilution of pool water with fresh water.  A buildup of by-products can damage the electrolytic cell.

Summary of Contents for PureLink













































Reviews: