background image

Page 8

Section 3. Installation Instructions Model APURE700 and APURE1400

3.1 Materials 

and 

Tools

NOTE

  Salt not included. See pages 17 - 20.

Installation Materials Furnished

Tools Needed for Installation

(1 ea.) 

Electrolytic Cell with 2”-2.5” Universal Unions

(1 ea.) 

Port Plug with 16 ft (4.88 m) Sensor and O-Ring

(3 ea.) 

Universal Union Nut

(1 ea.) 

16 ft (4.88 m) DC Power Cord

(1 ea.) 

Power Supply/Control Center

(4 ea.) 

Anchors and Screws

(2 ea.) 

Wire Nuts

(1 ea.) 

Owner’s Manual - Warranty Information

Tape Measure

Phillips & Flathead Screwdrivers

Pliers

Hacksaw

Voltmeter to determine line voltage of AC wiring to power supply

Electric Drill Motor and 1/4 “ masonry drill bit for mounting power supply on 
block or stucco wall

An NSF

®

 approved All Purpose Cleaner Primer

An NSF

®

 approved All Purpose Cement (such as Weld-On 794, 793)

3.2 Plumbing 

Confi gurations

  WARNING

When using electrical products, basic precautions should always be followed, including the following:

•  DANGER: RISK OF ELECTRIC SHOCK WHICH CAN RESULT IN SERIOUS INJURY OR DEATH. 

Before attempting installation or service, ensure that all power to the device is disconnected/turned 
off at the circuit breaker. Connect only to a circuit protected by a ground-fault circuit-interrupter 
(GFCI).

•  Grounding is required. The unit should be installed by a qualifi ed service representative and

should be properly grounded. (See Earth Bonding, page 11).

•  Install to permit access for servicing.

•  Read Cautions and Important Instructions on page 4.  

Before attempting any electrical wiring, be 

sure to read and follow Safety Instructions.  Wiring should only be attempted by a qualifi ed 
professional.

Summary of Contents for AquaPure APURE700









































Reviews: