background image

Page 24

Chlorine Production Rate 
(more or less) Adjustment  
with AquaLink RS Online 

The AquaLink RS Control System must be set to Service Mode before 
you can change the chlorine production levels from the AquaPure 
Service Panel. 

AquaLink RS Power Center

Press the Mode Select button to move the AquaLink RS from Auto 
Mode into Service Mode. The indicator light located next to the Service 
will turn ON.
Press the Valve Select button to choose either Pool Mode to change pool 
chlorine production, or Spa Mode to change spa chlorine production.
Press the Filter Pump button to turn on the pump and apply power to the 
AquaPure system.

AquaPure Service Panel

Press the arrow button 

A

 or arrow button 

B

 to change the 

CHLORINE 

PRODUCTION

 in 5% increments.  Generally, adjustments to production 

should be made in 10% increments.

AquaLink RS Power Center 

Press the Mode Select button to put the AquaLink RS in the Time Out 
mode.
Press the Mode Select button again to place it back into Auto mode.

NOTE 

The Power Center must be in pool mode to change the AquaPure pool setting; it must be in spa mode to 
change the AquaPure spa setting, use the valve select button to switch between the two modes. System 
must be cycled through SERVICE, TIME OUT, then back to AUTO to accept the Pool Setting versus the Spa 
Setting. 

NOTE 

When a pool pump timer is used to limit chlorinator run time, the 24 hours will only count down when the 
chlorinator is on. 

Temperature

 Press 

the 

Temperature

 button 

D

 to check the pool water temperature. 

Temperature measurements can be displayed in either Fahrenheit or 
Celsius. For more information, see Section 8, 

Temperature Conversion

.

Summary of Contents for AquaPure APURE700









































Reviews: