Jamara Audi R8 Spyder V10 performance quattro, Instruction

Page: 7 / 16

7
GB
1. Mounting the wheels
Place the body with the underside facing up. Press the button in the middle of the wheel and
push the wheel all the way down onto the axle. Release the button and and now pull the wheel
until it locks into place with an audible „click“. Repeat this on the other sides. Check that all
wheels are firmly seated by pulling on the wheel. If the knob on the rim sticks out a little,
the wheel is correctly locked in place.
2. Mounting the transport wheels
Fit the transport wheels to the rear of the model as shown.
3. Battery connection
Connect the plug from the battery to the model (A to A) and make sure the polarity is correct.
Check that all the connectors (B and C) are connected. Check the power supply by pressing
the ON/OFF switch on the model. If the power supply is working, you will hear a motor noise.
4. Assembling the seat
Position the seat, making sure that the pins on the seat engage with the holes in the body.
When the position is correct, secure the seat with screws.
5. Mounting the steering wheel
Connect the cable from the steering wheel to the cable from the model.Test the horn and music
button to make sure the connection works. Place the steering wheel in its designated position
(correct position, horn on the right, music button on the left). Align the hole through which the
screw comes. Insert the bolt and tighten it with a nut.
6. Fitting the windscreen and rear-view mirror
Press the windscreen into position until it clicks into place and secure it with screws. with
screws. Press the rear view mirrors into position until they click into place.
7. Charging your vehicle
•
The power swich must be turned in OFF position when charging.
• Insert the charger into the socket - the LED lights up green. Connect the charger to the
charging socket.
•
The LED on your charger lights up red as long as the battery is being charged. If the LED
lights green again, the battery is fully charged.
•
The charge time is 6 hours.
• Do not charge the battery more than once within 24 hours.
•
Charger and battery heat up during the charging process.
Attention!
•
Let the model cool ovv sufficiently after each use before putting it back into operation.
Whenn using an additional batteries let it cool off for minimum 15 minutes until the
model is operated again. Overheating can damage the electronics or may result in fire.
• Always disconnect the battery from the charger immediately after charging. Always
disconnect the charger from the power supply immediately after disconnecting the
battery. Inserting the rechargeable battery or charger after charging will result in damage
to the battery, charger or the power supply (fire hazard).
• Use the charger only in dry rooms.
Soundboard
1 USB
2
Micro SD
After inserting a Micro SD card or USB stick, the soundboard starts playing the tracks one after
the other. Only files with the extension .mp3 can be played back.
3 Aux
Connect MP3 device / mobile.
4
Music/V-
Press = previous, long press = Volume down
5
Story/pause & play
6 Music/V+
Press = Next, long press = Volume up
7 Song button
8 Voltage disply
Attention!
Your vehicle displays the total voltage of the two batteries in volts immediately after switching
on. The fully charged batteries will usually display a total voltage of approx. 12.6-13 volts
unloaded. The display is load dependent. This means that the displayed voltage will drop under
load. If a voltage of less than approx. 11.8V is displayed in the unloaded state, you should switch
off the Ride-on and charge the battery (see charging procedure). Otherwise the battery may be
deeply discharged and irretrievably damaged.
Otherwise, the battery may become deeply discharged and be irretrievably destroyed.
A deeply discharged battery is not covered by the warranty and must be replaced at
a charge. .
2
3
4 5 6 7
8
1
Functions
1 Soundboard
2 Shift Lever:
Forward▲: Press the shift lever on the „Forward ▲“ position.
Press the foot pedal, the model drives forward.
Stop O : The model will brake automatically, when your child‘s foot remove from the
foot pedal. Press the shift lever in the middle.
Reverse▼: Press the shift lever on the „Backward▼“ position.
Press the foot pedal, the model drives backwards.
Important!
The vehicle must be stationary before changing direction. Otherwise the gear unit and/or
the motor could be damaged.
3 ON/OFF Switch
With the ON/OFF switch you start the vehicle.
4 Light button
5 Foot pedal
6 Steering wheel
a Music
b Horn
1
3
5
6
4
7
8
2
Functions transmitter
1. Forward
2. Backward
3. Speed
4. Speed display
5. Left
6. Brake
7. Right
8. Battery compartment
Fitting the batteries
Observe the polarity..
Battery warning:
Non-rechargeable batteries are not to be recharged!
Do not open! Do not dispose of in fire!
Do not mix old and new batteries!
Do not mix alkaline batteries, standard (carbon-zinc) or
rechargeable batteries!
Rechargeable batteries are to be removed from the toy before
being charged!
Rechargeable batteries are only to be charged under adult
supervision!
The supply terminals are not to be short-circuited!
Binding transmitter and model
Press and hold the forward (1) and reverse (2) buttons simul-
taneously until the speed indicator light (4) flickers. Now switch
on the car and you will see that the speed indicator light stops
flickering, which means that the binding process was successful.
Now the model can be controlled with the transmitter.
1
2
3
4
5
6
b a